Availability of Replacement Awning Strut for Part Numbers 24934 3108392147

Question

Question:

THE STRUT ON MY AWNING WENT KAPUT. THE NUMBER ON IT IS #24934 3108392147. WOULD YOU HAVE THIS ITEM?

asked by: Thomas C

0

Expert Reply:

Based on the info I was able to find for your awning strut the replacement you'd want is the part # LC260282.

expert reply by: Jameson C

0

Answer 1

I reached out to Lippert and your 346005 control module was replaced with the Replacement Control Module for Lippert Ground Control 3.0 Leveling System #LC85ED. To use this control module they said you must have the Control Panel #LC421484 otherwise…

view full answer...

Answer 2

Yes, the Replacement Control Module for Lippert Ground Control 3.0 Leveling System #LC85ED will work as a replacement, however according to Lippert you need to have the Replacement Control Panel for Lippert Ground Control 3.0 and Travel Trailer RV…

view full answer...

Answer 3

I went ahead and pulled this Replacement I-Beam Jack Bracket #LC349975 from our warehouse to measure. I have attached the dimensions below. Hope this Helps.

view full answer...

Answer 4

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 5

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 6

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 9

Torque specs for wheel lug nuts will vary depending on the diameter of the lugs, type of lug nut and the wheel's material. The linked chart details the recommended torque for many combinations. Dexter Hub/Drum #84546UC3 has 1/2-inch studs and…

view full answer...

Answer 10

Below is the general process for bleeding an electric over hydraulic brake actuator like #K71-650. Fill reservoir with NEW brake fluid. Never re-use brake fluid that has been salvaged or removed from another system. Remove the key from the breakaway…

view full answer...

Answer 11

You can get a new brake mounting flange for your axle. The old flange will need to be cut off. The part is #4-44-1. This is designed to fit a 3 inch trailer axle and should be welded in place by a professional. Since you would also have to get the…

view full answer...

Answer 12

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Availability of Replacement Awning Strut for Part Numbers 24934 3108392147

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching