Boat Trailer Jack Recommended for a Coupler Height between 15 and 24 Inches High
Question:
I need to get a boat trailer jack with similar features as the DL67MR except that I only need 800-1000 lbs. The coupler height needs to be between 15" and 24 inches high. Do you have a recommendation for a USA manufactured with the above specs?
asked by: Robin I
Helpful Expert Reply:
Yes! For a boat jack that is similar to the # DL67MR that provides you with the smaller capacity you need, that is the Swivel Marine Trailer Jack with Caster Wheel - Bolt On - Sidewind - 10" Travel # DL84MR. The bracket height from the top of the bracket to the ground is 15-1/2" when retracted and 25-9/16" when extended. With this height range, that fits into your coupler height requirements. As far as compatibility, the jack fits maximum trailer tongue heights of 24-3/4" and fits square trailer tongues up to 3" x 5". To top it all off, this jack is 100% made in the U.S.A.
I went ahead and attached a video that walks you through the features and measurements.
Products Referenced in This Question
Dutton-Lainson Boat Trailer Jack w/ Wheel - Sidewind - Swivel - 10" Travel - Zinc - 1.5K
- Trailer Jack
- Boat Trailer
- Leveling Jacks
- Tongue Jacks
- Steel
- 1001 - 2000 lbs
- Sidewind Jack
- Swivel Jack
- 10 Inch Lift
- Bolt-On
- With Wheel
- Dutton-Lainson
more information >
Product Page this Question was Asked From
Dutton-Lainson Boat Trailer Jack w/ Wheel - Sidewind - Swivel - 10" Lift - Zinc - 1,000 lbs
- Trailer Jack
- Boat Trailer
- Leveling Jacks
- Tongue Jacks
- Steel
- 0 - 1000 lbs
- Sidewind Jack
- Swivel Jack
- 10 Inch Lift
- Bolt-On
- With Wheel
- Dutton-Lainson
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Search Results: trailer jack
- Shop: etrailer Surge Brake Coupler Lock - 3-3/8" Span - 1/4" Diameter - Chrome
- Shop: Demco Channel Tongue Trailer Coupler - Zinc - 2-5/16" Ball - 3" Channel - Bolt On - 18K
- Shop: Dutton-Lainson Boat Trailer Jack w/ Wheel - Sidewind - Swivel - 10" Travel - Zinc - 1.5K
- Shop: Dutton-Lainson Boat Trailer Jack w/ Wheel - Sidewind - Swivel - 10" Lift - Zinc - 1,000 lbs
- Shop: Pull Pin, Easy Swivel Trailer Jack with 8" Wheel - Sidewind - 1,500 lbs. by Dutton-Lainson
- Search Results: demco 18k
- Search Results: 2848dat
- Search Results: coupler pins locks
- Search Results: trailer lock keyed alike
- Search Results: spare tire mount
- Search Results: f26zr
- Q&A: How to Provide Power to Trailer Reverse Lights
- Shop: Master Lock Hitch Receiver and Coupler Latch Lock Set - Swivel Design - 2" Hitches
- Shop: Master Lock Hitch Receiver and Coupler Latch Lock Set - Padlock - 1-1/4" and 2" Hitches
- Video: Review of Dutton-Lainson Trailer Jack - 1K Marine Trailer Jack with Caster Wheel - DL84MR
- Video: Review of Dutton-Lainson Trailer Jack - Swivel Marine Trailer Jack - DL67MR
- Q&A: Length of Fulton Jack # FXP15L In Stored Position
- Article: Trailer Jacks
- Q&A: How Often to Lube Fulton Jack # FTJ12000101 Through Zerk Fitting
- Q&A: Will the Easy Swivel Trailer Jack # DL22800 Install Around a 3 x 5 boat Trailer Tongue
- Q&A: My Curt Swivel Trailer Jack is Harder to Lubricate after Adding Grease
- Video: Blazer Trailer Lights - Tail Lights - C7493RTM Review
- Video: Fulton Round Snap-Ring Swivel Marine Jack Review
- Video: Dutton-Lainson Sidewind Swivel Trailer Jack Review
- Video: etrailer Round Swivel Marine Jack with Wheel Review MJ-1206B
- Video: Optronics GloLight LED Trailer Tail Light Review and Installation
- Q&A: What is the Bracket Height on the DL22800 When Fully Retracted
- Q&A: Hub and Brakes for Vintage Camper With Dexstar Wheels
- Article: Trailer Maintenance Schedule