Replacement Operator Mechanism and Lift Arm For a MaxxAir Model 4951KS

Question

Question:

max air model 4951KS Can you tell me the proper lift mechanism for the above unit? The part no. I have is 10-20281K-1AF. I will order two of whatever you suggest as a replacement, one as a spare.

asked by: Ken K

0

Expert Reply:

The correct replacement operator mechanism for your MaxxAir model 4951KS is the Replacement Operator Mechanism for MaxxAir MaxxFan # MA10-20281K-1AF.

If you are needing the lift arm, it would be the Replacement Lift Arm for MaxxFan Roof Vents # MA10-20222KS.

expert reply by: Scott S

0

Answer 1

Yes the operator replacement part #MA10-20281K-1AF that you referenced will work as a replacement for your Maxxfan #4951ks.

view full answer...

Answer 2

Yes you are correct the Replacement MaxxFan Plus 4-Speed Roof Vent with White Lid #MA00-04751KSX is the right replacement and measures 18 1/8" long and 16 1/2" wide, which is the same measurements as your current MaxxFan Plus Roof Vent w/…

view full answer...

Answer 3

Based on what you are describing it sounds like this is coming from the motor. There wouldn't be anything that would leak out of the operator mechanism. I recommend wiping it up and keeping an eye on it to see if you can better identify where…

view full answer...

Answer 4

The model number for your MaxxAir vent like the MaxxAir MaxxFan Mini Roof Vent w/ 12V Fan #MA00-04401M, can be found on a sticker stamped on the upper side, if you can't find it there you can also find it located on the bottom and visible when…

view full answer...

Answer 5

To determine your current opening size you will want to measure the rough opening on your trailers' roof. Make sure to remove the garnish ring in your roof's opening to get an accurate measurement. The most common openings is 14 1/4" x…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 9

In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14". To pick the correct cover, you will also…

view full answer...

Answer 10

The two most likely causes of a MaxxAir vent fan lid not opening or closing are either going to be a lift motor or operator failure. I recommend removing the motor and applying power directly to this to see if the shaft turns. If not, you know the…

view full answer...

Answer 11

Thanks for the pictures of your roof vent lid Marty! Based on that the correct replacement is the Ventline part #BVD0449-A01 that you referenced if you wanted white or the part #BVD0449-A03 for the same smoke color you have now.

view full answer...

Answer 12

The model number for fans such as the MaxxAir MaxxFan Mini Roof Vent, #MA00-04401M is listed on the upper side of the assembly itself. Please see the attached image. You will best identify this by opening the vent and climbing on top of the RV.…

view full answer...