Does Curt Hitch C13418 Have 5/8 inch Diameter Hitch Pin Hole

Question

Question:

Does Curt 13418 hitch have 5/8 inch hole for Curt 22323 pin or 1/2 inch hole for Curt 22321 pin?

asked by: Dan

1

Helpful Expert Reply:

The Class III Curt trailer hitch part # C13418 that you referenced has a 5/8 inch diameter hitch pin hole which is standard for the 2 inch hitch size. So the Curt anti-rattle device 22323 part # C69HR would fit.

expert reply by: Jameson C

1

Answer 1

Some accessories fit more loosely than others in any given trailer hitch. If you think that the receiver is getting worn out, I recommend measuring the inner opening width and height to see if it is still at 2-1/2 inches. Also check the accessories…

view full answer...

Answer 2

Yes, the Curt Anti-Rattle Kit for Hollow Shank #C69HR will hold up when pulling your equipment trailer. This will only work on ball mounts for a 2" receiver with a hollow shank. I feel the Blue Ox Hitch Receiver Immobilizer II #BX88224 is the…

view full answer...

Answer 3

If you have a hollow shank ball mount you can use this anti rattle device #C69HR. One part will insert into the ball mount shank and you can use the threaded pin to take out the excessive rattling you're experiencing.

view full answer...

Answer 4

Although the #30717 will work, I have a better suggestion for you. If your F150 is the New Body style, use part #118247. If you have the Old Body style, use #118242. Either connector will plug inline with your existing trailer connector, allowing you…

view full answer...

Answer 5

Yes, there is a trailer hitch receiver fit for your 2024 Chevy Blazer (so long as it is not the Premier model); I verified this fit directly with the manufacturer for you. The correct part is the following: - Curt Trailer Hitch Receiver #C13418 If…

view full answer...

Answer 6

There are a lot of wires and connectors under the rear of your 2022 Buick Envision Preferred but if you check out the attached picture you can see what the connector you are looking for looks like to know if you can use the part #C56325 or not.

view full answer...

Answer 7

Yes, you can absolutely pull a 1500 lb trailer with a 2021 Chevy Blazer. Looking at the online owners manual for the Blazer it looks like there is some variance in towing capacity across different models. For example, Blazer 3LT and Premier trims are…

view full answer...

Answer 8

Yes, for your 2020 Chevy Blazer we have the Curt Class III Trailer Hitch Receiver #C13418, which is a perfect fit and will line right up to existing holes in the frame rails for a simple bolt-on, no-drill installation. It will provide you with a…

view full answer...

Answer 9

The best class III hitch for your 2023 Chevy Blazer is going to be the etrailer Trailer Hitch Receiver item #e36YR. This hitch is custom fit and bolts directly to your Blazer with included hardware. I really like the etrailer item #e36YR hitch…

view full answer...

Answer 10

Good question. When installing a hitch like the etrailer Class 3 Hitch #e36YR on a 2024 Chevy Blazer, there is more than one way to get the bolts inside the frame rail. What we recommend doing is simply pulling the hardware through the hole at the…

view full answer...

Answer 11

The easiest hitch to install on your 2024 Chevy Blazer is the etrailer Class 3 Hitch #e36YR. All of the other hitches we offer for the 2024 Blazer will require full removal of the rear bumper, while the #e36YR will not. This will make for a much…

view full answer...

Answer 12

When using the Replacement 2" Hitch Adapter part #853-7489 you will need to use a 12mm hitch bolt such as the Thule Snug Tite Hitch Lock part #THSTL2 or the Replacement Threaded Pin for Thule Snug Tite Hitch Lock part #853-5917. You will also…

view full answer...

Does Curt Hitch C13418 Have 5/8 inch Diameter Hitch Pin Hole

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching