Does the Yakima and the Trailer Coupler for Yakima Rack and Roll Trailers Come With Hardware

Question

Question:

I am looking to replace the coupler as it has rusted out along with the bolts that attach this piece to the main shaft. If I order this replacement part, will it come with the nuts and bolts as well?

asked by: Johnny

1

Helpful Expert Reply:

I reached out to Yakima and the Trailer Coupler for Yakima Rack and Roll Trailers - 2" Ball - Bolt On # Y08123 does not come with hardware since it is designed to use your existing hardware. Yakima also had no information on what hardware would be used as a replacement. I recommend taking what you have to the local hardware store to make sure you get the right size replacement nuts and bolts.

expert reply by: Robin H

1

Answer 1

The thickness of the T-bolt head of the part #Y8880184 you referenced is 5/32 of an inch. I attached a picture that has all of the other dimensions as well. These T-bolts are M10 x 1.5 x 25

view full answer...

Answer 2

Yakima has the T-bolt kit part #Y8880184 which includes a quantity of 4 T-bolts that are designed to fit in the tracks of their roof channels like what you have. These come with lock nuts as well.

view full answer...

Answer 3

It sounds like you're looking for the Replacement T-Bolt with Nut for Yakima Rack and Roll Trailers part #Y8880184 which are used to attach the towers to the frame.

view full answer...

Answer 4

On the Channel Tongue Trailer Coupler - Trigger Latch - Zinc - 2" Ball - Bolt On - 3,500 lbs, #CT-3001-Z, you referenced the distance between the mounting holes is 3-1/16 inches center to center. It is the same separation for each set. Each hole…

view full answer...

Answer 5

The Trailer Coupler for Yakima Rack and Roll Trailers #Y08123 was designed specifically for Rack and Roll 78 inch #Y08107 or 66 inch #Y08106. If you were looking for a coupler for your trailer and have a 2" wide trailer tongue I recommend the…

view full answer...

Answer 6

The Replacement T-Bolts for Yakima Universal Mount Crossbar Clamp - Qty 2 #8860061 are 3" and are designed for the ReelDeal and ShowBoat 66 carriers. These were the bolts you referred to.

view full answer...

Answer 7

The T-bolts in the Yakima Replacement T-Bolt with Nut for Yakima Rack and Roll Trailers #Y8880184 are going to measure 3/8" x 1" long. The next size up would be 3" long, but if you can let me know the product you're trying to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 10

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 11

When it comes to installing The Timbren Rear Suspension Enhancement System #TFRRGR on your 2020 Ford Ranger they come in a pair. The Timbren springs has a 6,000 pound weight capacity, and no drilling is required during the installation. I attached an…

view full answer...

Answer 12

Mad-Ramps states that the part #MR54FR is best suited for ATVs/UTVs with one row of seats but if the width of your golf cart is less than 60 inches and the wheel base is less than 88 inches this would work for you.

view full answer...

Does the Yakima and the Trailer Coupler for Yakima Rack and Roll Trailers Come With Hardware

Product Page this Question was Asked From

Continue Researching