Could Mad-Ramps be Used with 6 Passenger Golf Cart

Question

Question:

Can you tell me if mad ramps can be used with an advanced EV six passenger golf cart and a 2000 Chevy Silverado Thank you

asked by: Buddie F

0

Expert Reply:

Mad-Ramps states that the part # MR54FR is best suited for ATVs/UTVs with one row of seats but if the width of your golf cart is less than 60 inches and the wheel base is less than 88 inches this would work for you.

expert reply by: Jameson C

0

Answer 1

When it comes to installing The Timbren Rear Suspension Enhancement System #TFRRGR on your 2020 Ford Ranger they come in a pair. The Timbren springs has a 6,000 pound weight capacity, and no drilling is required during the installation. I attached an…

view full answer...

Answer 2

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 3

I reached out to Mad Ramps about the MAD-MOUNT Wall Mount Brackets for Mad-Ramps Pivoting ATV/UTV Ramps part #MR27DR and they informed me that the brackets are both 36" long x 2-1/2" tall. I have attached a photo below with this as well.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Mad-Ramps states that the part #MR54FR is best suited for ATVs/UTVs with one row of seats but if the width of your golf cart is less than 60 inches and the wheel base is less than 88 inches this would work for you.

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The AllTrek 4000 kits provide the best cushioning so if you were to upgrade from your CRE3000 kit to the Alltrek you would see a big improvement. If you have a 35 inch wheelbase you'd want the part #MR29DR or if you have a 33 inch wheelbase…

view full answer...

Answer 9

It appears that your u-bolt plate on your 2021 Grand Design Reflection 31MB, will work with the SumoSprings Trailer Helper Springs #SS26MV. The plate itself including the bends does not appear to be larger than 3/4" nor does the width appear to…

view full answer...

Answer 10

Hey Patrick, so for your leaf spring upgrade I am going to need to know a couple of things before I can get you over to the right part. Specifically, the length from eye to eye, the spring width, leaf thickness, and the number of leaves. From here I…

view full answer...

Answer 11

Personally I wouldn't go with Timbren's for your needs. They're essentially rubber bump stops that prevent your suspension from flexing when weights placed on the rear of your Canyon. The major issue with them is comfortability when you…

view full answer...

Answer 12

The brackets on the SumoSprings Trailer Helper Springs #SS26MV are 1-1/2" wide so they will fit evenly across the humps on your spring pads. I do not recommend cutting down the spring and you will be able to use these even with only having…

view full answer...

Could Mad-Ramps be Used with 6 Passenger Golf Cart

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching