Thinnest Material LED Trailer Mini Clearance Light w/ Grommet Will Fit

Question

Question:

interested in #mcl10akb whats the thinnest material this light can be installed through without flopping around.

asked by: Joseph M

0

Expert Reply:

The thinnest material is 1/16" to fit the LED Trailer Mini Clearance and Side Marker Light with Grommet # MCL10AKB.

You can connect the wires with the 22-18 Gauge Butt Connectors # 05730-5.

expert reply by: Kyle S

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 5

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 6

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 7

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Yes, the Kenda Karrier ST175/80R13 Radial Trailer Tire #AM31990 will indeed fit on the etrailer Hitch Mounted Spare Tire Carrier #e98ZR. The spare tire carrier will work with virtually any 4 lug, 5 lug or 6 lug wheel. The #AM31990 wheel uses the…

view full answer...

Answer 10

Hey Derrick, the good news is yes it does exist. So what you're going to want is the Hydraulic Trailer Brake Kit - Uni-Servo - Free Backing #AKFBBRK-35 for brakes, and the 10" Hub and Drum for 3.5K Axle #AKBD2-545-97 for the hub and drum.…

view full answer...

Answer 11

Hey Kevin thanks for your question. There is not much downside to going with the 5,000 lb springs instead of the 3,500 lb. A higher rated spring may make the ride a bit more "chunky" at times, since the spring would not flex as easily.…

view full answer...

Answer 12

The best way to power the interior lights in your trailer is with its own independent battery. You will not want to use the breakaway battery. The breakaway battery is only designed to operate the breakaway and will drain extremely quickly,…

view full answer...

Thinnest Material LED Trailer Mini Clearance Light w/ Grommet Will Fit

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching