Trailer Hitch for a 2022 Hyundai Sonata Hybrid

Question

Question:

Will this fit on a 2022 Hyundai Sonata Hybrid?

asked by: Daniel G

1

Helpful Expert Reply:

I confirmed with Draw-Tite and yes, the Draw-Tite Sportframe Trailer Hitch Receiver item # DT74MR will fit the Hybrid model of the 2022 Hyundai Sonata.

If you need a wiring harness you will want the Tekonsha T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector item # TK97FR. This harness allows you to control the lighting functions on your trailer or accessory.

For a ball mount you'd need the Draw-Tite Drawbar item # 3593 and then for hitch balls item # 19258 for a 2 inch ball or item # 19256 for a 1-7/8 inch ball.

expert reply by: Jerred H

1

Answer 1

Yes it does; per the manufacturer the correct Draw-Tite trailer hitch that fits your 2023 Hyundai Sonata hybrid is the following: - Draw-Tite Sportframe Trailer Hitch Receiver #DT74MR

view full answer...

Answer 2

The trailer hitch options for a 2021 Hyundai Sonata do require removal of the heat shield. I recommend the Draw-Tite Sportframe Trailer Hitch Receiver part #DT74MR which is a class I hitch with 1-1/4" receiver tube opening. The heat shield…

view full answer...

Answer 3

The heat shield of the 2020 Hyundai Sonata gets in the way of the Draw Tite hitch part #DT74MR from fitting. If you check out the included instructions you can see that the hitch installs on top of where the heat shield sits.

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 11

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 12

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...