Can I Use the Saris Swing Away # SAR36VR with the Kuat Transfer V2 2-Bike Rack?

Question

Question:

Will the Saris Access Swing Away Hitch Extender fit a Kuat Pivot v2 two bike rack?

asked by: John P

0

Expert Reply:

I believe you meant to ask about the Kuat Transfer V2 2-Bike Rack # KU74FR (for 1-1/4" and 2" hitches) or the # KU84FR (for 2" hitches). If this is what you meant, you can use these racks with the Saris Swing Away Hitch Extender # SAR36VR.

expert reply by: Bob C

0

Answer 1

For your 2019 Honda Odyssey, there are only the raised side rails or no rails. Based on your photo and description, I recommend the SeaSucker Monkey Bars Roof Rack - Vacuum Cup Mount #298-SX6000B. Each vaccum cup has a pull strength rating of 210…

view full answer...

Answer 2

When the tongue weight capacity of a hitch is determined the manufacturer factors in the typical ride quality issues like you mentioned. So etrailer rated their hitch #e98855 as having a dynamic tongue weight capacity of 525 lbs. This means that the…

view full answer...

Answer 3

The SeaSucker Monkey Bars Rack #298-SX6000B has a cup size of 6". The only SeaSucker products that have the smaller 4.5" cups are for Marine use.

view full answer...

Answer 4

Good catch, and I verified with Timbren that the capacity is indeed 3,500 lbs for their springs that fit your 2019 Honda Odyssey: - Timbren Rear Suspension Enhancement System #T26FR As for overloading the #T26FR when towing a 3,500 lb trailer and 400…

view full answer...

Answer 5

It is not recommend to mount the Saris Swing Away Hitch Extender for Bike Racks item #SAR36VR upside down so that it swings to the drivers side. The weight from the bike and rack when not extended is sitting on top of the receiver mount. If you were…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

Thanks for the picture! For your 2023 GMC Sierra 1500 with adaptive ride control you'll want the Air Lift LoadLifter 5000 Air Helper Springs item #AL57388. This air bags have a 5,000 lbs load leveling capacity that will keep the rear end of your…

view full answer...

Answer 12

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...