Recommend U-Bolts For A 72 Inch Long 2,000 Pound Axle

Question

Question:

does the u bolts come with the new axle

asked by: Mark E

0

Expert Reply:

When it comes to The Trailer Axle with Idler Hubs - 5 on 4-1/2 Bolt Pattern - 72 inch Long - 2,000 pounds # e37YR the U-bolt kit does not come with it. The U-Bolt Kit for Mounting 2,000-pound, Round Trailer Axles - 4-1/4 inch Long U-Bolts # APUBR-10 is the kit you would need to work with the # e37YR.

I will attach a review video link below.

expert reply by: Noah E

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 3

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 4

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 5

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 6

I have attached for you below some common torque values needed for a trailer suspension system but a lot of these will vary by bolt size and other factors. U-Bolts: Varies by Size - 1/2" bolts: 45 ft/lbs - 70 ft/lbs, 9/16" bolts: 65 ft/lbs…

view full answer...

Answer 7

I contacted MORryde and this does happen from time to time as the weight of the trailer can spread out the axles due to downward pressure on the springs/suspension. Odds are the 35" wheel base #MR27ZR will be the correct one for you, but they…

view full answer...

Answer 8

Since Grand Design is kind enough to list certain parts for their trailers I can confirm you have a 33" wheelbase on your 2020 Grand Design Transcend 27BHS. This means the MORryde Rubber Equalizers #MR87ZR will fit your trailer. Although I'm…

view full answer...

Answer 9

Well shackle length is mainly based on the height difference between the front and rear hangers. The rear hanger normally doesn't hang as low as the front so that the shackle can offset the difference and add the ability to move. What is the…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

Yes, axle spread and wheel base by definition are the same measurements. You will measure from the center of one axle to the center of the 2nd axle to determine what you axle spread is. This may be difficult as some wheels and covers will make this…

view full answer...

Answer 12

The absolute best cushioned equalizer that fits the dimensions you mentioned having would be the MORryde ALLTREK 4000 part #MR89DR as this is only option to provide vertical and horizontal cushioning. This would make a big difference and you'd be…

view full answer...