How To Attach Inside Wires On Go Power Solar Cable Entry Plate with Red and Black MC4 Cables

Question

Question:

I see where you connect the solar panels to the mc4 connectors , but as far as the 2 cables coming inside do you have to splice mc4 connectors?. I have a ecoflow pro solar generator . thank you .

asked by: Steve S

0

Expert Reply:

The blunt cut red and black wires on the Go Power Solar Cable Entry Plate with Red and Black MC4 Cables part # 34273842REVA that go to the inside would just simply attach to the battery or any sort of solar controller you're using, this would just require standard wiring connectors like butt connectors or ring terminals. That said, you will need to make sure you use the appropriate size wires on the inside to extend and fuse protection outlined by the solar panel manufacturer.

expert reply by: Conner L

0

Answer 1

The wiring of the Go Power Solar Cable Entry Plate with Red and Black MC4 Cables #34273841REVA is tinned copper.

view full answer...

Answer 2

The Go Power Overlander Solar Charging System Item #34282181 will be the same. The part number could've changed because the manufacturer may have added a few extra components like connectors, terminals, etc. The system itself will not function…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Yes, our Dexter leaf spring part #DX74XR is the same as the part number 072-079-00. This is a 7-leaf spring for an 8,000 lb trailer axle that is 24-7/8 inches.

view full answer...

Answer 7

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...