Recommended Brake Controller For 2019 Nissan Armada With Factory Tow Package

Question

Question:

2019 nissan armada platinum i have factory harness what do you recommend for brake controller. Thanks

asked by: Kenzie M

0

Expert Reply:

We can get your 2019 Nissan Armada with the factory tow package set up with a trailer brake controller, and since you have the tow package all you'll need is the brake controller and wiring adapter. For your '19 Armada I highly recommend an option from Tekonsha:

- Tekonsha BRAKE-EVN Trailer Brake Controller # TK63VR

- Tekonsha Plug-In Wiring Adapter # 3050-P

I really like the BRAKE-EVN # TK63VR because it is the best overall value for a trailer brake controller; the reason for that is its unique combination of quality and cost-effectiveness. The BRAKE-EVN is going to give you smooth braking, is easy to use, and has a bright display that is simple to read.

For a combination of quality, reliability, and price, there really isn't a better option for your 2019 Nissan Armada than the BRAKE-EVN.

expert reply by: Kyle S

0

Answer 1

If your 2017 Nissan Aramada is the same as the Infinity QX80 as you referenced, then the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Nissan and Infiniti #3050-P will connect to the brake control wiring harness underneath the dash…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 6

There is a trailer hitch receiver as well as a 4-way wiring harness that fit your 2022 Jeep Grand Cherokee WL; that said, we don't have any way to reference a VIN so you'll need to confirm if you do have the WL, which is the new model of…

view full answer...

Answer 7

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The brake controller port on a 2021 Ford F-150 (if equipped) will be located behind the coin tray in the center console. This will be accessed by removing the panel under the steering wheel. I have attached a video which shows this below. For a brake…

view full answer...

Answer 10

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Recommended Brake Controller For 2019 Nissan Armada With Factory Tow Package

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching