What Roof Rack do You Carry that Uses the Rhino-Rack RCP66-BK on My 2021 Chevy Traverse?

Question

Question:

Hello, im looking for rcp66-bk... do you guys have a different part number for it ? Thanks

asked by: Edyta S

0

Expert Reply:

We definitely have it! Part rcp66-bk is a Rhino-Rack part number. Here at etrailer, that part is the Custom RCP Fit Kit for 4 Rhino-Rack RC and RV Series Roof Rack Legs - Fixed Mounting Points # RR32SV.

Judging by the fact that you are looking at this fit kit, I assume you have raised rails on your 2021 Traverse. To complete the Rhino-Rack setup that includes the # RR32SV, you need the following parts:

- Rhino-Rack Vortex Aero Crossbars - Aluminum - Black - 46" Long # RRVA118B-2
- RCL Legs for Rhino-Rack Crossbars and Pioneer Platforms - Fixed Mounting Points # RRRCL4
- All-Metal Lock Cores # RRVA-LEC4

With this system, you gain the benefit of an extremely aerodynamic design that leads to a quieter ride and greater fuel efficiency. Since the channels run the entire length of the bars, you can mount compatible t-slot accessories. As far as weight capacity, the rack has a maximum of 220 pounds. I recommend consulting with your owner's manual to make sure your vehicle can handle the weight you wish to transport.

expert reply by: Bob C

0

Answer 1

Thanks so much for the photos! I can see how you might be confused. I went ahead and confirmed with Yakima that these rails are considered flush rails with fixed mounting points on your 2022 Chevy Bolt EUV. For a great roof rack system for your…

view full answer...

Answer 2

It is possible to cut the Rhino-Rack crossbars but I do not recommend this as it will certainly void the warranty. Since we offer Rhino-Rack's Vortex Aero bars in various lengths you can simply choose the individual parts you prefer to make up…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

There are a couple of differences between the two. The JetStream bars like #Y00425 are made of extruded aluminum while the CoreBars such as the #Y00421 you've looked at are constructed of galvanized steel. As you've mentioned, the CoreBar has…

view full answer...

Answer 7

Yakima's Skyline towers part #Y53TR can fit the tracks of the Retrax XR that you have with the landing pad 1 part #Y00221 but there isn't a way with the Baseline towers. Your Yakima Corebar or Jetstream bars will work with the Skyline towers…

view full answer...

Answer 8

According to Rhino Rack, if you were to go with the shorter bars, you'll only have 1-1/4 inch of leeway on each side which isn't enough in their opinion. I'd recommend going with the 71 inch bars so you'll be certain of a good fit. As…

view full answer...

Answer 9

Yes, the Roamer LT Roof Rack for Pop-Up Campers and Camper Shells #S80510 will fit your 2023 Forest River Flagstaff 176LTD. It is also what I recommend to add a roof rack for a bicycle carrier on your camper. Once installed you will be able to add…

view full answer...

Answer 10

There is a trailer hitch receiver as well as a 4-way wiring harness that fit your 2022 Jeep Grand Cherokee WL; that said, we don't have any way to reference a VIN so you'll need to confirm if you do have the WL, which is the new model of…

view full answer...