Mounting Bracket to Use with Blue Ox 7-Wire to 6-Wire # BX88206

Question

Question:

What is the bracket I will need for a Blue Ox Bx88206? Your video shows a bracket that you no longer carry.

asked by: Randy S

0

Expert Reply:

The Hopkins universal mounting bracket part # HM48625 would be a great option to use as a mounting bracket for the connector of the # BX88206.

expert reply by: Jameson C

0

Answer 1

To install the RoadMaster 6-Wire Trailer Connector, part #RM-910030-7, you will need a bracket. The bracket I recommend is the Roadmaster Bent Electrical Socket Bracket, part #RM-910030-5. You need to find a flat surface that can support the…

view full answer...

Answer 2

To keep a maintenance charge on the battery of your Honda I recommend using a wiring harness like part #BX88206 with your tow bar wiring that you can run a wire from the connector at the front of the CR-V to the battery. If the connector at the back…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

When it comes to choosing between the Blue Ox Patriot #BLU37TR and the Brake Buddy Select 3 #HM39524, these systems are extremely similar in their setup and functionality. Both of these systems provide proportional braking in a compact and easy to…

view full answer...

Answer 5

Hey Mark, so the correct Blue Ox base plate kit to use with the Blue Ox Ascent tow bar part #BX4375. is the part #BLU53FR. For lighting you can use #C96JR, and not have to worry about cutting into the taillight housing as this plugs inline with the…

view full answer...

Answer 6

What you need is a light kit specifically for flat-towing. The Plug-N-Tow TM Vehicle Wiring Harness, #42615, would be if the Jeep were towing a trailer and not for activating its lights while it is being towed. There are a few options for lighting…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 9

Hey Robert, for your 2016 Jeep Wrangler using the Ready Brute Elite II tow bar you can use the Blue Ox Base Plate Kit #BX1126 with the Blue Ox Base Plate Adapter Brackets for Ready Brute Elite Tow Bars #BX88297. From here, to complete your flat…

view full answer...

Answer 10

Hey Ken, so the first thing you will need is a base plate kit like the Blue Ox part #BLU85CR which fits your 2023 GMC Canyon and would be compatible with your Blue Ox tow bar. I do not know what braking system you had in the past but for a permanent…

view full answer...

Answer 11

Either way is correct. It depends on if you want to keep the semi-style 7-Way (if you need to tow that type of trailer) or if you will never be towing a semi-trailer. If you need to keep the 7-Way semi active on the truck, then you would need to make…

view full answer...

Answer 12

Hey David, actually what is going to make the biggest improvement in handling and stability for your 2011 Itasca is an upgraded rear sway bar with the part #RM-1139-175. I know that's not what you asked about but for motorhomes where most of the…

view full answer...

Mounting Bracket to Use with Blue Ox 7-Wire to 6-Wire # BX88206

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching