Replacement Rod And Nut For A Ram Trailer Jack Model 1200 Series

Question

Question:

Ram Trailer Jack Model 12000 Series 20,000lb support capacity 10,000lb lift capacity Is this the correct not and rod?

asked by: Vinny

0

Expert Reply:

Yes, the Replacement Rod and Nut for etrailer and Ram Square, Direct Weld Jacks # TJD-12000-RODNUT does fit your Ram Trailer Jack Model 1200 Series.

I have also included a review video for you to check out as well.

expert reply by: Bryce D

0

Answer 1

Good news! I was able to get a exploded diagram as well as a set of instructions on how to replace the rod and gears #TJD-12000-RODNUT in the #12000 Series Ram Jacks made after 2012. I have attached them to this page for your convenience. Basically,…

view full answer...

Answer 2

For your 12K Pacific Rim square jack the correct inner tube with drop leg is the part #TJD-12000SP-FIP. This is a direct replacement for the Ram/Pacific Rim 12K trailer jacks like #TJD-12000SP-F2, which are often used as OEM/factory units on newly…

view full answer...

Answer 3

The Ram 12k Jack will use the Replacement Square, Direct Weld Jack Inner Tube with Spring-Return Drop Leg #TJD-12000SP-FIP.

view full answer...

Answer 4

If the jack you have is the brand RAM then yes the part #TJD-12000-RODNUT would work for it. We have it branded for etrailer.com jacks but they also fit RAM jacks.

view full answer...

Answer 5

The Replacement Rod, Nut, and Grease Trap #TJD-12000-RODNUT is a fit for the 12000 series of Ram or etrailer jacks such as #TJD-12000SP-R2. It is specifically designed for square, direct-weld TJD-12000 Series jacks; the lift nut will fit 3-1/2"…

view full answer...

Answer 6

The Replacement Rod and Nut for etrailer and Ram Square, Direct Weld Jacks #TJD-12000-RODNUT would work on your 14K Big Tex 14OT-26GN if the jacks you have are Ram 10k or 12k landing gear style jacks. We don't have a way to know what jacks your…

view full answer...

Answer 7

We do not have this item in stock for me to measure its thread pitch but two of us estimated it as being 6 or 7 threads per inch. I linked a photo of the instructions to replace this part. The bearing is removable and is available as a replacement…

view full answer...

Answer 8

We have several replacement parts for the internals of a Ram brand square jack. The Replacement Rod and Nut #TJD-12000-RODNUT will fit the following Ram jacks: #TJD-12000SP-F2 10K Sidewind with 12-3/8 inches of travel w/handle #TJD-12000SP-R2NH 10K…

view full answer...

Answer 9

The bearing is not included with the Replacement Rod and Nut for etrailer and Ram Square, Direct Weld Jacks - 12K part #TJD-12000-RODNUT. There is a bearing washer at the top but the bearing is sold separately as the Replacement Bearing for etrailer…

view full answer...

Answer 10

I would almost guarantee that the #TJD-12000-RODNUT is the correct part you need since you said you have a RAM brand trailer jack. This is designed to fit square RAM jacks like what you have so this would be what you'd want most likely. Feel free…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Replacement Rod And Nut For A Ram Trailer Jack Model 1200 Series

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching