Correct Replacement Bearing for Ram Square Direct Weld 12K Jack
Question:
My Ram jack has a lower bearing just as you show but it also has a upper bearing that sits just below the horizontal gear. I don’t see any option for that bearing on your exploded view. Do you stock the upper bearing? Thank you,
asked by: Tim O
Expert Reply:
The bearing is not included with the Replacement Rod and Nut for etrailer and Ram Square, Direct Weld Jacks - 12K part # TJD-12000-RODNUT. There is a bearing washer at the top but the bearing is sold separately as the Replacement Bearing for etrailer and Ram Square Jacks part # TJD-12000-BR. If you take a look at the attached exploded view of the jack, you'll see there is a bearing at the top above the washer but no bearing on the bottom. I have attached an install video of said parts as well.
It sounds like you may have a different model/series and in which case I would need to know what that is to assist.
Products Referenced in This Question
Replacement Bearing for etrailer and Ram Square Jacks - 10,000 lbs
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Hardware
- Bearings
- etrailer
more information >
Product Page this Question was Asked From
Replacement Rod and Nut for etrailer and Ram Square, Direct Weld Jacks - 12K
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Hardware
- Rod
- etrailer
more information >
Continue Researching
- Shop: Replacement Rod and Nut for etrailer and Ram Square, Direct Weld Jacks - 12K
- Shop: Replacement Bearing for etrailer and Ram Square Jacks - 10,000 lbs
- Search Results: tjd~12000~rodnut
- Shop: Replacement Bearing for etrailer and Ram Square Jacks - 7,000 lbs
- Q&A: Thread Pitch of Replacement Rod and Nut for TJD-12000 Direct Weld Jacks
- Video: Bulldog Jacks Replacement Thrust Bearing Review
- Video: Review of etrailer Replacement Rod And Nut etrailer Ram Square Jack - TJD-12000-RODNUT
- Video: Rebuilding of an etrailer or Ram Square Jack
- Shop: Replacement Thrust Bearing for Bulldog Round Tube Trailer Jacks with 5,000-lb Capacity
- Video: Review of etrailer Replacement Bearing TJD-12000 Series Jacks 10K LB Lift Capacity - TJD-12000-BR
- Video: Rebuilding the etrailer and Ram Square Jacks
- Shop: Replacement Return Spring for etrailer and Ram Square, Direct Weld Jacks - 10,000 lbs
- Shop: Replacement Sidewind Gear Kit for etrailer and Ram Square, Direct Weld Jacks - 10,000 lbs
- Shop: Ram Gooseneck Coupler w/ Load Bearing Pin - 8" Adjustment - Square - 2-5/16" Ball - 25K
- Search Results: jack handle
- Video: Review of etrailer Replacement Return Spring etrailer Ram Square Direct Weld Jack - TJD-12000-RSP
- Video: Review of etrailer Replacement Handle Shaft etrailer Ram Square Direct Weld Jack - TJD-12000-SHABUS
- Q&A: What Size O-Ring Is Needed For The Replacement 2-Quart Pump Reservoir Kit?
- Q&A: Troubleshooting Slide-Out Function Where Solenoid Clicks But Doesnt Move Motor
- Q&A: Warranty Length for Replacement Hydraulic Pump Motor for Lippert Hydraulic Power Unit
- Q&A: No Power To Lippert Ground Control 3.0 Control Panel
- Q&A: Slide Out Periodically Doesn't Work On 2010 Keystone RV Hideout Series M30 BHDS
- Q&A: Replacement Top and Thrust Bearings for 12K Weld-On RAM Jack
- Search Results: rv battery box strap
- Search Results: trailer brake away switch
- Shop: Suspension Enhancement
- Shop: Gooseneck Hitch
- Article: Choosing the Right Suspension Kit for Your Truck and Trailer
- Search Results: bd1824200100
- Search Results: bulldog jack screw and nut