Brake Light Signal Wire Color on a 1996 K2500 Pickup Truck to Install a Brake Controller

Question

Question:

I am wiring a brake controller into 1996 K2500, what color wire is considered the brake cold wire activates when brake pedal is pressed to send signal?

asked by: Kevin

0

Expert Reply:

GM traditionally used a white wire for the brake light signal wire at the stop light switch wire on the C/K series pickup trucks.

I strongly recommend testing the wires before you make your connections. The best way to ensure you are using the correct wire is to use a circuit tester to test for the wire that only shows power when the brake pedal is pressed. The wire should not have power with any other function. If you do not have a circuit tester, I recommend using # PTW2993.

expert reply by: John H

0

Answer 1

The four wires and their functions are: White: Ground wire, connected to negative side of battery. Blue: Electric brake wire, ran to the brake output circuit of your 7-way with 10 gauge wire like #10-1-1 sold by the foot. Black: 12v power wire,…

view full answer...

Answer 2

You'll be looking for a white wire coming off the brake stoplight switch located at the top of the brake pedal. However, you don't actually need to do that, the 2006 Silverado actually has a connector under the dash in the junction…

view full answer...

Answer 3

Brake controllers such as #C74VV will have constant power once installed. They need to have constant power otherwise they would reset every time you turned off the vehicle. Brake controllers have what is basically a sleep mode. After a certain…

view full answer...

Answer 4

Having the factory fuse is perfectly fine for an aftermarket brake controller. The benefit of a circuit breaker is that it can reset itself so you do not have to replace a fuse should it blow. So you are good to go with the 30 amp factory fuse…

view full answer...

Answer 5

I recommend using part #3015-P to easily install the brake controller. You just cut off the black connector on the adapter and wire it to the matching colors at the back of the brake controller. The other end of the harness plugs into the junction…

view full answer...

Answer 6

You will need to hard wire the Tekonsha #TK63VR, on your 1996 Chevrolet CK Pickup. Hard wiring is straight forward and fairly easy to do. We have instructions and a video that I have linked below for you. From the Brake controller here are your…

view full answer...

Answer 7

The controller is only putting out voltage when the manual switch is applied on the brake controller, but not when the vehicle brakes are applied, is that correct? The most likely problem is that the controller is not getting the input that the…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 12

The Redarc Tow-Pro Liberty #RED24FR is the way to go over the Elite #RED44FR as you get the nicer functions of the Elite at a lower price. The Elite has the ability to be the more preferred proportional style of controller as well as a time-delayed…

view full answer...

Brake Light Signal Wire Color on a 1996 K2500 Pickup Truck to Install a Brake Controller

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching