Parts Needed To Convert Electric Over Hydraulic To Electric Brakes On Dexter 15,000LB Axle

Question

Question:

Convert Hydraulic over electric to all electric Dexter 15,000# Can it be done? Can I still use the the same drums? Could you provide parts list and or numbers if it can be done.

asked by: Tim H

0

Expert Reply:

To confirm that the Dexter Electric Brake Kit # 23-446-447 will operate properly on your Dexter 15,000lb axle you will need to confirm that your hub is compatible with electric brakes.

The Dexter Trailer Hub and Drum Assembly # DX78QR for a 15,000lb axle, you can see the smooth surface inside the drum where the mounting bolts are that confirms it will work with electric brakes.

The only other parts you will need is some 12 Gauge Wire # 12-1-1 to run from the 7-way connector to the brakes and the Connectors # DW05745-5, # 44-5310A to splice the wiring together and ground to the frame. I have included a image showing how the wiring will need connected at the axles. You will be able to reuse your breakaway system with the electric brakes.

expert reply by: Bud M

0

Wiring For Electric Trailer Brakes
(click to enlarge)

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 5

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 8

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 9

The recommended lug nut torque for your 7,000lb axle depends on a few factors like wheel size, stud size etc. Check out the attached photo which shows the torque specs for a variety of applications. I see you were looking at the Dexter Nev-R-Adjust…

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 11

There really isn't a particular maximum trailer weight that is used to determine when brakes need to be added to both axles of a tandem axle setup. While I do still recommend checking your local laws, I am also not aware of any general laws that…

view full answer...

Answer 12

I spoke to Dexter and they said there is a bit of a process for installing the spindle nut properly. 1. You will need to thread on the inner nut, rotate the hub, then tighten the nut to 100 foot pounds. 2. Loosen the nut to remove the torque, making…

view full answer...