Availability of the Handle Bushing for a Fulton Jack

Question

Question:

Im looking at this item Replacement Sidewind Handle Kit for Pro Series or Fulton Marine Jacks Item # F0933305S00 Only need the bushings, Do you sell the bushings separately? if so, what is the item number. Thnaks

asked by: Bruce D

0

Expert Reply:

The bushing in the Replacement Sidewind Handle Kit for Pro Series or Fulton Marine Jacks # F0933305S00 is only available in the kits. We do not have it available on its own.

It is also available in gear kits like the Replacement Bevel Gear Kit # F0933302S00.

expert reply by: Scott S

0

Answer 1

We do not offer a gear kit specifically for the Reese 74410 trailer jack but there is a good possibility that the Replacement Bevel Gear Kit for Fulton Jacks, #F0933302S00, will work for you. I have included a picture which lists the dimensions of…

view full answer...

Answer 2

Based on the 1-1/8" diameter x 1/2" thick measurements you provided of your current gears, the Replacement Fulton Gear Kit #F0933302S00 would be the correct gear kit for your older Fulton jack as it includes two bevel gears that are…

view full answer...

Answer 3

The beveled gear kit that you have referenced, #F0933302S00, is designed for Fulton jacks with capacities ranging from 800 to 1,200, so this should be the correct set for your 1,000 pound model. To make sure, you can compare the measurements of the…

view full answer...

Answer 4

Thank you for providing the photo of your Fulton jack handle as well as the clear description of the compatibility issue you've encountered with the jack repair kit you purchased, part #F0933302S00. My contact at Fulton was able to confirm that…

view full answer...

Answer 5

It is likely based on the capacity of the jack that you will need bevel gear kit, #F0933302S00, that you have referenced. You may be able to find more information about the jack by looking at the cap or for numbers near the bottom of the inner/outer…

view full answer...

Answer 6

The Replacement Gear Kit for etrailer and Ram Round Swivel Marine Jacks part #MJ-1000B-GR have a 1/2" inner diameter and 1-1/8" outer diameter.

view full answer...

Answer 7

The Replacement Bevel Gear Kit #F0933306S00 is for applications. The #F0933302S00 will fit the following Fulton jack models: TJ503/C, TJU503, PMJ53, TJ507/C, PMJ75, CS750, GR700/TJ712, XP10/6/W/WC and XP100. Since your jack is as old as it is and you…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Availability of the Handle Bushing for a Fulton Jack

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching