What Cargo Carrier and Anti-Rattle Device do You Recommend for My 33.4x27.6x 28.4 Generator?

Question

Question:

I have a 445 fifth wheel camper with a 2 trailer hitch. I am looking for a way to carry a Honda EU7000iS generator. The generator is 33.4x27.6x 28.4L x W x H and is 270lb. Do you have something you would recommend. From my research the biggest issues seems to be the hitch bouncing and the hitch breaking... Thanks

asked by: Vern V

0

Expert Reply:

For a generator that measures 33.4 inches long x 27.6 inches wide x 28.4 inches high and weighs 270 pounds, I recommend using the 32x48 Reese Solo Cargo Carrier for 2" Hitches - Steel # PS1040100. This cargo carrier is approved to withstand the added force/torque on the back of your fifth wheel camper. We've had many neighbors who have given this carrier rave review when used on a trailer. The inside dimensions of the Reese carrier are 47-3/4" long x 31-3/4" wide x 2-3/4" deep.

As far as theft-deterrence and keeping the carrier secure to the hitch during transport, I strongly recommend the Anti-Rattle Trailer Hitch Receiver Lock for 2" Hitches # 63232 Not only does this lock protect your investment, but it also provides you with a tight fit that connects the shank of the carrier to your hitch. This pin dramatically reduces any shank movement and vibration during movement. For even more support against movement and vibration, you can also use the etrailer Anti-Rattle Hitch Stabilizer for 2" Hitches - Vinyl Coated Steel # e99007.

To make sure that your generator sits nice and snug on the platform, I recommend using the Erickson Cam Buckle Tie-Down Straps w/ S-Hooks - 2" x 8' # EM34409. The S-hooks will attach to the tie-down openings along the wide rails of the carrier.

As with all hitch accessories, I recommend confirming with your trailer's owner's manual that you can safely transport the weight of the cargo you wish to transport.

expert reply by: Bob C

0

Answer 1

We have an option that may work for you, but there isn't a bumper-mounted cargo carrier that is deeper than 24 inches. The best option we have is to add a bumper-mounted hitch to accommodate a deeper carrier; what you can use are the following: -…

view full answer...

Answer 2

A smaller hitch extender like the Curt part #C45791 would work to give you the additional clearance for your Hollywood Racks RV Rider part #HLY64FR that you need.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

With the size of your Champion Generator 200953(23.4" wide, 27.9" long and 21.7" tall I recommend using the 32x48 Reese Solo Cargo Carrier #PS1040100. This has a 47-3/4" long by 31-3/4" wide inner tray and can support up to…

view full answer...

Answer 6

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 7

The total height from the bottom of the receiver tube to the top of the closed GearLocker on the Yakima Exo Swing Away Storage System #Y74ZR is 42-1/2 inches tall. I went ahead and attached a diagram that shows this height for your convenience.

view full answer...

Answer 8

That is a keen observation and a good question. I actually had the chance to assist with assembly of one of the Flint Hill Goods 30" x 50" Wheelchair Carriers #FHG99ZR not too long ago. The main bolt for the shank is indeed quite large, so…

view full answer...

Answer 9

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...