6-Pin Round Vehicle Connector To 7-Pin Round Commercial Trailer Connector

Question

Question:

I am looking for a 6 pole to 7 pole adapter. The 6 round is on the truck side and the 7 pole is on the Commercial trailer side. Can you point me in the right direction?

asked by: Tyler M

0

Expert Reply:

I have a couple options as there is not one adapter from a 6-pin round vehicle connector to a 7-pin round commercial trailer connector.

The first will combine a Adapter 6-Pole to 7-Pole Trailer Wiring Adapter # 47435 and a Pollak Trailer Connector Adapter # PK12727 to adapt your connections.

Or you can wire in a Pollak 6-Pole, Round Pin, Trailer Wiring Connector # PK11604 to a Pollak Heavy-Duty, 7-Pole, Round Pin Trailer Wiring Socket # PK11720. This will create your own wiring adapter. You will need to source the correct length wiring from your local automotive or hardware store for the adapter. I have included wiring images for both connectors.

expert reply by: Bud M

0

7-Way Connector Wiring
(click to enlarge)

6-Way Connector Wiring
(click to enlarge)

Answer 1

Though we can get you what you will need you will have to assemble it. There are three parts that you will need to make a round 7-way round pin connector they're listed below: The Male 7-Way Round Connector #PK11702 Jacketed 7-Way Wiring (Sold by…

view full answer...

Answer 2

It sounds like you want a diagram of the wiring for your trailer and breakaway system. I am attaching an article with pictures about wiring trailers. I am also attaching an article with pictures on wiring a breakaway kit. I also recommend making the…

view full answer...

Answer 3

Yes, the Sentry Deflector for Demco Tow Bars #DM9523135 will work with the Demco Commander II Non-Binding Tow Bar #DM9511012 that you mentioned!

view full answer...

Answer 4

The Curt A25 5th Wheel Trailer Hitch for Ram Towing Prep Package #C16046 will work well with the Roto-Flex pin box. The combination will be a good match for you and this hitch with the specific connection to the factory prep package pucks will make…

view full answer...

Answer 5

You will want to have a total of 6 inches of clearance between the bed rails of your truck and the overhang of your trailer when it is sitting level and connected to your 2004 Ford F-150. The overall height of most fifth wheel hitches puts them below…

view full answer...

Answer 6

We do have 6-Pole Square Trailer Wiring Connector Kit (Car and Trailer Ends) #37995 that you can use for your Arctic Fox camper. This is both the male and female ends. But the wires on them are 18 gauge. You could replace the ground and power wires…

view full answer...

Answer 7

Yes, the Kenda Karrier ST175/80R13 Radial Trailer Tire #AM31990 will indeed fit on the etrailer Hitch Mounted Spare Tire Carrier #e98ZR. The spare tire carrier will work with virtually any 4 lug, 5 lug or 6 lug wheel. The #AM31990 wheel uses the…

view full answer...

Answer 8

Your best option is going to be to use the wiring diagram I attached for 6-ways to identify the functions of the wires from the picture you sent in and then wire them according to the labelled pins on the new 7-way similar to the #HM48502 and…

view full answer...

Answer 9

A 100 amp hour battery would suffice for powering a trailer tongue jack as well as some other accessories. For this, we have both AGM such as the Bright Way Deep Cycle RV or Marine Battery part #BRW94FR. In order to charge these batteries, you'd…

view full answer...

Answer 10

Either way is correct. It depends on if you want to keep the semi-style 7-Way (if you need to tow that type of trailer) or if you will never be towing a semi-trailer. If you need to keep the 7-Way semi active on the truck, then you would need to make…

view full answer...

6-Pin Round Vehicle Connector To 7-Pin Round Commercial Trailer Connector

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching