Solution for Using Equalizer Weight Distribution System When Upgrading Trailers

Question

Question:

My current trailer has a tongue weight of 810# and trailer weight of 8600# gross. I plan on upgrading trailers in the near future. Is the 1400#/14000# hitch too much for the current trailer?

asked by: Eric

0

Expert Reply:

Yes, the Equal-i-zer Weight Distribution System w/ 4-Point Sway Control - 14,000 lbs GTW, 1,400 lbs TW # EQ37140ET will be overrated and cause a stiff, bumpy ride and potential problems with your current trailer. The tongue weight range for this WDH is 1,000-1,400 lbs and ideally you want your tongue weight to be somewhere in the middle. However, I do have a solution for you.

I recommend getting the Equal-i-zer Weight Distribution System w/ 4-Point Sway Control - 10,000 lbs GTW, 1,000 lbs TW # EQ37100ET. This puts the tongue weight of your current trailer right in the middle of the 600-1,000 lb range. Then, when you upgrade trailers in the future, you can purchase the Replacement Spring Bars for Equal-i-zer Weight Distribution Systems - Qty 2 - 1,400 lbs TW # EQ90-01-1499. This will allow you to use the same WDH with the heavier trailer without having to get an entirely new system.

I have attached some review videos for your reference.

expert reply by: Robin H

0

Answer 1

Based on the weight range you think you'd have of 980-1,472 lbs the Equal-i-zer kit you'd want would be the part #EQ37140ET that you mentioned. Since it's a travel trailer the likelihood of the tongue weight being a bit higher than 10…

view full answer...

Answer 2

I spoke with my contact at Equal-i-zer who said that the arms of the 14K Weight Distribution (WD) system #EQ37140ET and the 12K WD system #EQ37120ET are compatible with each other. In fact, he said they are the exact same bars. The difference between…

view full answer...

Answer 3

It is usually possible to replace the spring bars in a weight distribution hitch setup so long as the two sets of bars are the same type, both trunnion style for instance, and both are from the same generation of hitch. A 10-year-old setup may not be…

view full answer...

Answer 4

The best way to pick out a weight distribution system is to base it off of the loaded tongue weight of the setup when it is loaded and ready to tow. This figure also includes the weight of any cargo behind the rear axle of the tow vehicle. I attached…

view full answer...

Answer 5

It completely depends on the amount of trailer sway you are experiencing and the conditions you are towing in. The ProPride 3 Weight Distribution Hitch w/ Sway Control for 2-1/2" Receivers item #PR47QR uses pivot-point projection technology that…

view full answer...

Answer 6

The Replacement Spring Bars for Equal-i-zer Weight Distribution Systems #EQ90-01-1299 weigh approximately 22lbs each.

view full answer...

Answer 7

The Equal-i-zer Weight Distribution System w/ 4-Point Sway Control part #EQ37140ET would be a bit too overrated for a 7,500-8,000 lb trailer and if used there would some negative effects such as ineffective sway control. That said, it's pretty…

view full answer...

Answer 8

The key to weight distribution is not to have an exact percentage of the weight transferred to either of the axles. The whole goal behind all of if it is to have your tow vehicle sit as level as possible so that it will brake and handle the best…

view full answer...

Answer 9

To determine if you have the correct system for your trailer tongue weight, you should determine the fully loaded and ready to tow tongue weight of your trailer. The weight of any gear stowed behind the rear axle of the tow vehicle also needs to be…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...