Dimensions and Pin Size For Round, Pipe Mount Swivel Jack # TJP-5001S-B

Question

Question:

Do you have spec for the PIN diameter / size that comes with this jack?

asked by: Craig

0

Expert Reply:

The Round, Pipe Mount Swivel Jack # TJP-5001S-B uses a 5/8" Diameter Pull Pin # TJP-PN58. The jack slides onto a 2" diameter weld on pipe that is included.

expert reply by: Bud M

0

Round, Pipe Mount Swivel Jack # TJP-5001S-B Dimensions
(click to enlarge)

Answer 1

The Round, Pipe Mount Swivel Jack w/ Footplate #TJP-2002S-B uses a 9/16" Diameter pull pin. Just like the replacement pull pin and chain #TJP-PN916. The hole on the mount is just over 9/16" so that the pin can fit. I attached a short review…

view full answer...

Answer 2

It sounds like the right hand turn and brake signal lights are not working on your trailer. If that is the case then the first place to check as you mentioned is the fuse box. In the fuse box located under the hood of your 2016 Ram 3500 you will want…

view full answer...

Answer 3

We have had great reviews for the Rampage Radiant Backseat Heater part #RA3501. It uses a 12V power source so you can wire it directly to the battery of the Cub Cadet. As long as you are using it while the ATV is started it should not drain the…

view full answer...

Answer 4

The overall length of the pin part #TJP-PN58 is 3-15/16 inches.

view full answer...

Answer 5

Hey there Gary, thanks for the photo and yes the etrailer Bolt-On Swivel Mounting Plate for 3,500-lb Trailer Jacks with a 5/8" Swivel Pin #e52JR will indeed work with your Round, Pipe Mount Swivel Jack #TJP-5001S-B.

view full answer...

Answer 6

We have just the thing! The Replacement Male Pipe #TJP-IP916 is going to be the correct weld-on male pipe mount for the #TJP-5001S-B jacks. If you need the female side to weld to the jack itself it will be part #TJP-OP916.

view full answer...

Answer 7

The Ark Drop Down Corner RV Stabilizer Jacks #AR94FR are definitely better than just standard scissor jacks, but the JT Strong Arm Stabilizers #LC191025 are a better option since they distribute the weight across the frame to help strengthen the…

view full answer...

Answer 8

The etrailer Bolt-On Swivel Mounting Plate #e52JR has a 2" outer diameter on the round tube which is 3/16" thick.

view full answer...

Answer 9

The overall height of the Round, Pipe Mount Swivel Jack #TJP-5001S-B is 16-3/4 inches when fully retracted and 26-3/4 inches when extended. Basically from the center of the pipe mount to the top of the jack measures 6-1/2 inches.

view full answer...

Answer 10

Since you are not getting the 12V power when your truck is running, you most likely don't have a fuse issue as you stated their isn't a specified fuse or relay in the owners manual. The issue is that your truck is computerized even at the…

view full answer...

Answer 11

For your Fulton F2 Swing-Up Trailer Jack, Dual 7" Wheels, Sidewind, Bolt-On - 1,600 lbs #F1413020134 part number 9 you referenced is not a replacement option. The outer tube components are not replaceable according to my contact at Fulton. That…

view full answer...

Dimensions and Pin Size For Round, Pipe Mount Swivel Jack # TJP-5001S-B

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching