Correct Replacement Air Lift Air Bag for 2007 Chevy Silverado 2500

Question

Question:

Need an airlift 5000 replacement bag for my 2007 Silverado 2500hd reg cab long bed Duramax 4x4. I dont know part number

asked by: Christopher L

0

Expert Reply:

If you have the Air Lift LoadLifter 5000 Air Helper Springs part # AL57275 which is a fit for a 2007 Chevrolet Silverado 2500 then the correct replacement is the Replacement Air Spring for Air Lift LoadLifter 5000 part # AL50290.

expert reply by: Conner L

0

Answer 1

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 5

Gen-Y's calculation for pin weight is a safe guess, but isn't the most accurate so the only way you'll get the correct capacity Gen-Y 5th Wheel Pin Box is to fully load the trailer and go to a commercial scale to measure the pin weight.…

view full answer...

Answer 6

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 7

There should be a sticker or plate on the pin box itself that lists the manufacturer and model of the pin box. If it is not present then there are some measurements you can take to determine the model of the pin box. I have included a link that…

view full answer...

Answer 8

The Gen-Y Hitch 5th Wheel to Gooseneck Pin Box part #GY58GR is primarily designed for long bed trucks. It's no different than a standard fifth wheel pin box in regards to the size. If you were using a fixed hitch and standard pin box before with…

view full answer...

Answer 9

The difference between the 1621 and the 1621SHD is weight capacity and how many bolts is required to mount it. The 1621 uses 4 bolts for mounting. The 1621SHD requires all 6 bolts to be used.

view full answer...

Answer 10

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 11

We have the following Gen-Y shock absorbing 5th wheel pin boxes which are compatible with the Lippert Rhino pin box bolt pattern. The weights listed below are the maximum capacities the pin box is capable of supporting. 21,000 lbs - 3.5K TW #GY86GR…

view full answer...

Answer 12

The best way to prevent any clearance issues with your 2022 KZ Durango Gold G356RLQ and your 2020 Chevrolet Silverado 2500 with 6-1/2' bed and factory puck system is by using the Demco Autoslide 5th Wheel Hitch #DM79GV. This hitch slides back and…

view full answer...

Correct Replacement Air Lift Air Bag for 2007 Chevy Silverado 2500

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching