Replacement Top Plug and Manual Crank Handle for Lipper Power Tongue Jack 1817941

Question

Question:

I bought a trailer that is missing the top plug on the power tongue jack where you would manually operate that jack. Jack is model number 1817941 - Lippert? Can I purchase this from you? Also missing the manual tool to operate the tongue jack if I had no power. Please advise. Thanks.

asked by: John

1

Helpful Expert Reply:

The replacement top plug you are looking for that fits your Lippert Jack 1817941 is the 2 Inch Replacement Cap for Lippert Trailer Jacks # LC115863. Unfortunately we do not have a replacement for the manual crank handle.

expert reply by: Robin H

1

Answer 1

We do have the correct replacement override plugs for your Lippert Power Tongue jack, though it is indeed different than the part number you mentioned; instead, what you will need is the following: - Replacement Override Plugs for Lippert Electric…

view full answer...

Answer 2

I do have some options for you but there is no guarantee that they will work unless you have the exact jack they are designed to fit. If you can provide me with the exact jack you have then I may have a better option for you but otherwise; part…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

The Lippert 2420801 hub is an 8k hub with an 8 lug bolt pattern so for a replacement you'd just need the part #8-285-10UC3-A.

view full answer...

Answer 8

We do carry the 33" Ark Stabilizer Jack that you are looking for with part #ARK77FR. I was able to track down a few drawings that you should find helpful. These are for the 30" #ARK94FR and the 24" #ARK34FR Stabilizer jacks. I'm…

view full answer...

Answer 9

I apologize for the confusion. It sounds like you have found some conflicting answers in the past, so I took the liberty to contact Bulldog directly and this is what they said: "The 12k RAM jack has a smaller diameter cross-shaft, therefore the…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

I contacted the manufacturer about the lengths for these stabilizer jacks and have included the information they were able to provide me. The Ark Drop Down Corner RV Stabilizer Jacks #ARK34FR are 422 mm (16.6") collapsed and 600mm (23.6")…

view full answer...

Answer 12

We don't currently have any customer submitted photos for the Brophy Heavy Duty Cable Camper Jacks #CX74, but we do for the lower capacity #CJ74, which uses the same lift brackets. From the edge of the tube to the lift bracket is approximately…

view full answer...