2017 Subaru Outback Wagon Parts Needed to Tow a Small Teardrop Trailer

Question

Question:

I have a 2017 Subaru Outback. I need a towing hitch with a 2 inch ball for a lightweight RV. the Tag XL, maximum weight 2,200 lbs. I will need to connect the lights and brakes. Can you tell me which products I need? thank you

asked by: Jane M

0

Expert Reply:

I recommend using the etrailer Ball Mount Kit # 989891 for towing with your 2017 Subaru Outback Wagon. This comes with a 3/4" rise/2" drop ball mount as well as 1-7/8" and 2" hitch ball, a hitch pin, and a ball mount storage bag for when you aren't towing.

For wiring I recommend the Curt T-Connector # C56040 because it has the highest amp capacity out of the wiring kits we have to offer.

If you don't already have a trailer hitch I recommend using the Draw-Tite Max-Frame Trailer Hitch Receiver # 76227 because the crosstube is hidden so it looks better and doesn't impede on ground clearance like some of the other trailer hitches do.

From what I could see it looks like your TAG trailer comes with electric brakes. Usually when a trailer is equipped with brakes it's recommended to use them so you have the best control over your trailer. If you choose to use the brakes you need some additional parts and for that I recommend the Wiring Upgrade Kit # ETBC7L along with the Curt Echo Brake Controller # C51180.

Attached are some installation videos for you to check out.

expert reply by: Jon G

0

Answer 1

I attached an install video that shows the trailer wiring harness part #118467 installed on a 2017 Subaru Outback like what you have. In it you can see exactly where to find the harness on your vehicle. There are several panels that need to come…

view full answer...

Answer 2

While there is a Draw-Tite hitch that fits your 2017 Subaru Outback, the part number you asked about is not a fit; that is a fit for the Forester, like you mentioned. Instead, for a similar hitch that does fit your '17 Outback and is a…

view full answer...

Answer 3

The Curt hitch receiver item #C13410 and the Draw-Tite hitch receiver item #76227 are identical hitches in almost every way. They both have the same capacities and installation methods and are hard to identify once they're installed on a Subaru.…

view full answer...

Answer 4

I have included a link to a video below that shows trailer wiring harness #118467 being installed on a 2017 Subaru Outback. The video shows you where to plug in the harness. The tool our installer uses to remove trim panels is the appropriately named…

view full answer...

Answer 5

Whenever the option is available, I'll always recommend choosing the 2 inch receiver over the 1-1/4 inch because the 2 inch has many more hitch mounted accessories available. The etrailer brand #e98847 and the Draw-Tite #76227 are both fine…

view full answer...

Answer 6

When it comes to capacity, installation procedure and appearance once installed you can pretty much toss a coin to choose between the Curt #C13410 or the Draw-Tite #76227, they are that similar. This being said, I'd always choose the Curt because…

view full answer...

Answer 7

I recommend going with the Draw-Tite #76227 . This hitch has a 2" receiver that won't interfere with the backup sensors on your bumper. This hitch has a 600-lb TW / 4000-lb towing capacity to maximize the towing capabilities of your 2019…

view full answer...

Answer 8

For your 2017 Subaru Outback Wagon we have trailer wiring that plugs into the connector at the rear of the vehicle like with the Tekonsha harness part #118467 which I recommend the highest. This installs easily and has the most reliable converter…

view full answer...

Answer 9

I definitely understand being a bit overwhelmed by the amount of options in front of you, however I can definitely help with differentiating the trailer hitches for your 2019 Subaru Outback Wagon along with explaining my personal recommendation,…

view full answer...

Answer 10

I believe you are referring to the 3 concealed cross tube hitches available for the 2019 Subaru Outback Wagon, Draw-Tite Class III part #76227, Curt Class III part #C13410 and EcoHitch part #306-X7601. The Draw-Tite part #76227 hitch is the best…

view full answer...

Answer 11

The main difference between the Curt Trailer Hitch Receiver part #C13410 and the Draw-Tite Max-Frame Trailer Hitch Receiver part #76227 is the manufacturer. They install the same way and offer the same weight capacities. Between the two there is no…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...