Replacement Mounting Bracket for Disc Brake Caliper

Question

Question:

Hi, Im wondering on part Item # K71-633-00, if you by chance sell or have a part number for the replacement mounting bracket. Thanks for your help,

asked by: Ryan H

0

Expert Reply:

Yes, we do have replacement mounting brackets but they will be in a different finish than the Dexter Disc Brake Assembly - 10" Hub/Rotor - 5 on 4-1/2 - E-Coat - 3,500 lbs item # K71-633-00. They are the:

Replacement Mounting Bracket for Disc Brake Caliper item # KCMB10RS in stainless.

Replacement Mounting Bracket for Disc Brake Caliper item # KCMB10RD in dacromet.

expert reply by: Jerred H

0

Answer 1

I wish I had a good answer for you, but since Kodiak was bought out by Dexter it seems they discontinued the 204 caliper in favor of using the 225 calipers. They both worked on 3500lb axles but the 225 was also able to be used on larger axles up to…

view full answer...

Answer 2

Yes we do. The calipers and brackets for the Kodiak Disc Brake Kit item #K2R35D can be purchased separately. The caliper is item #KDBC225DAC and the brackets are item #KCMB10RD. I have linked a diagram of the bracket for the Kodiak Disc Brake Kit…

view full answer...

Answer 3

I attached a picture that has all of the mounting hole dimensions of the Kodiak Disc Brake Bracket #KCMB10RD.

view full answer...

Answer 4

The Kodiak 225 calipers #KDBC225S fit 3,500 lb 10 inch assemblies as well as 12 inch rotors up to 5,200 lbs. The 204 calipers fit 3,500 lb axles with 10 inch assemblies. The 225 calipers are more prominent than the 204 calipers but they are not…

view full answer...

Answer 5

I spoke with my contact at Kodiak. He stated that the UA code at the end of your existing caliper mounting bracket means that it is for a slip over (over the hub) or stainless steel rotor. We have 2 that fit this category, each with a different…

view full answer...

Answer 6

What you'll want to do is refer to your instructions for the proper torque specs. For example, the instructions for the 5.2K - 6K Kodiak Disc Brake Kit #K2HR526D call for the brake mounting flange to be welded to the spindle and then the caliper…

view full answer...

Answer 7

From the research I did the Kodiak 225 calipers like the part #KDBC225DAC that you referenced are an exact replacement for the Mastercraft setup you currently have.

view full answer...

Answer 8

Thanks for the pictures! You're correct, the Replacement Mounting Bracket for Kodiak Disc Brake Caliper #KCMB10RD is the correct replacement mounting brackets for your Kodiak 225 brake calipers. Attached is a product overview video for you to…

view full answer...

Answer 9

Thank you for the photos. From what I can find, you currently have a Reliable ACT-7.5K brake actuator. Unfortunately, we don't carry replacement parts for your Reliable brake actuator. The best option that we can provide would be to replace your…

view full answer...

Answer 10

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Replacement Mounting Bracket for Disc Brake Caliper

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching