Dimensions of Roadmaster 690 Diode

Question

Question:

Please tell me what the dimensions of this are excluding the connector portion. I cant believe no one publishes them.

asked by: Dave D

0

Expert Reply:

The Roadmaster diodes like part # RM-690 are 2 inches tall by 1-1/2 inches wide not including the connectors for wiring.

expert reply by: Jameson C

0

Answer 1

I spoke with my contact at Roadmaster and he informed me that the Roadmaster Universal Brake Monitor #RM-9530 that you referenced will work without a breakaway kit installed. Reason being is that under normal circumstances the breakaway circuit of…

view full answer...

Answer 2

The Pacer Performance 3rd Brake Light Logic Module #PP20-702 filters out the turn signal and only illuminates the 3rd brake light when the brake pedal is pressed. I have attached a photo of the installation instructions for you to check out.

view full answer...

Answer 3

Wiring the camper shell brake light on your 2017 GMC Sierra 2500 is very straightforward. All you need to do is use the Pacer Performance 3rd Brake Light Logic Module #PP20-702, which has three wires: two yellow wires and a green wire. Simply tap…

view full answer...

Answer 4

The correct way to fix this would be to install a battery charger like #20011 on each of your break-away systems. This is a reasonably priced option that will prevent the overcharging of your breakaway battery and will also prevent the back feeding…

view full answer...

Answer 5

I do have some technical information for you about the Roadmaster Diodes #RM-690 and #RM-790, but I do not have any prints available. Both part numbers are 1/2" tall, 1-9/16" wide, and are 1-5/16" long. They can withstand up to 85 of…

view full answer...

Answer 6

The Ultra-Fab Power Twin II Electric Stabilizer for Trailers and RVs part #UF39-941707 is designed primarily for i-beam frames. If you have a tubular frame construction then you would first need to weld flat bottom supports to this in order to attach…

view full answer...

Answer 7

Generally a breakaway kit is installed mounting the battery to the frame but it doesn't have to be. We carry a few different chargers separate from the kits themselves and I've linked our selection for you. The most popular of the chargers if…

view full answer...

Answer 8

Ultra-Fab Stabilizer Jack #UF39-941707 will bolt onto a trailer using the bolt holes that are present on the mounting flanges of this jack as well as with the included nuts and bolts. You will most likely have to drill holes in the frame of your…

view full answer...

Answer 9

The HappiJac Swing-Out Extender Bracket for Dual Wheel Chassis Truck Camper Jacks #HJ54FR (single) or Swing Out Extension Brackets for HappiJac Truck Camper Jack Systems #LC182496 (double) are not compatible with the Atwood electric camper jacks.…

view full answer...

Answer 10

Your question came in blank, but I was able to see the picture you submitted that shows an RV/Toy Hauler that appears to be used to transport a helicopter and that you referenced Ultra-Fab Power Twin II Electric Stabilizer with Dual Motors…

view full answer...

Answer 11

The #UF39-941707 would only provide you with 2 inches of lift. If you wanted to carry some blocking with you to provide additional lift should you need it, this unit would work for you. However, since the #UF39-941705 with a 30 inch lift (which would…

view full answer...

Answer 12

Yes, you can use the Hopkins Trailer Breakaway Kit Battery Charger, #20011, with the motorcycle battery on your motorcycle trailer. Like you said, you would simply tie-off the blue wire since it will not be used. This charger will maintain the charge…

view full answer...

Dimensions of Roadmaster 690 Diode

Product Page this Question was Asked From

Continue Researching