What is Needed to Wire Truck Camper Shell Third Brake Light

Question

Question:

How do you connect the brake light on a cap on a 2017 Sierra 2500?

asked by: Chad

0

Expert Reply:

Wiring the camper shell brake light on your 2017 GMC Sierra 2500 is very straightforward.

All you need to do is use the Pacer Performance 3rd Brake Light Logic Module # PP20-702, which has three wires: two yellow wires and a green wire. Simply tap into your Sierra's turn signals with the yellow wires and run the green wire to the third brake light. What this module does is filter out the turn signals and lights up the brake light when you hit the brakes.

If you take a look at the cut out of the linked installation instructions I added you can see exactly how it wires.

expert reply by: Kyle S

0

click to enlarge

Answer 1

Typically stabilizer jacks and leveling jacks are the same thing. The Ultra Fab part #UF39-941705 can do both as well. It can lift up to 30 inches from where the jacks are mounted on the trailer. When the jacks are at their max height they have a…

view full answer...

Answer 2

The Ultra-Fab Power Twin II Electric Stabilizer for Trailers and RVs part #UF39-941707 is designed primarily for i-beam frames. If you have a tubular frame construction then you would first need to weld flat bottom supports to this in order to attach…

view full answer...

Answer 3

Since the Ultra Fab Landing Gear Set part #UF17-943010 that you referenced calls for 19-1/8 inches from the top of both of the weld stops and your setup currently has a distance of 19-1/2 inches you would have to move your current weld stops so that…

view full answer...

Answer 4

Generally a breakaway kit is installed mounting the battery to the frame but it doesn't have to be. We carry a few different chargers separate from the kits themselves and I've linked our selection for you. The most popular of the chargers if…

view full answer...

Answer 5

Yes, you can use the Hopkins Trailer Breakaway Kit Battery Charger, #20011, with the motorcycle battery on your motorcycle trailer. Like you said, you would simply tie-off the blue wire since it will not be used. This charger will maintain the charge…

view full answer...

Answer 6

You are correct in how to measure the lift of the stabilizer jacks. The distance is from the ground to the trailer frame when the trailer sits level. I would recommend you go with the 30 inch lift version of the Stabilizer Jack part #UF39-941707 that…

view full answer...

Answer 7

I contacted the manufacturer about the lengths for these stabilizer jacks and have included the information they were able to provide me. The Ark Drop Down Corner RV Stabilizer Jacks #ARK34FR are 422 mm (16.6") collapsed and 600mm (23.6")…

view full answer...

Answer 8

I do have a solution for you to have a working stabilizer again but unfortunately when I spoke with my contact at Lippert he said that the legs on your 198641 unit are not replaceable alone. Instead you will need to replace the whole stabilizer jack…

view full answer...

Answer 9

I would recommend the Ultra-Fab Deluxe Electric Landing Gear Set #UF17-943010. This set has the highest rating of all the landing gear sets we offer and has dual motors like you said you wanted. It's hard to say whether or not these will match up…

view full answer...

Answer 10

For the rear of your 2007 Fleetwood Tioga Class C 31M the Ultra Fab stabilizer part #UF39-941705 that you referenced would work well as long as your trailer frame is between 48 and 80 inches in width. The lift range is up to 30 inches so as long as…

view full answer...

Answer 11

The direct replacement for your Lippert Components model 113407 stabilizer jacks can be found with part #LC369774 on our site. My contact at Lippert confirmed that this is the correct replacement.

view full answer...

Answer 12

The part #20011 that you referenced is designed to charge a breakaway battery (which is very small). It sounds like you are looking for something to put a maintenance charge on a larger battery. Which if so you would instead want to run a length of…

view full answer...

What is Needed to Wire Truck Camper Shell Third Brake Light

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching