Replacement Brake Actuator For Atwood 61101

Question

Question:

need atwood hitch 61101 parts u have model listed but nothing came up

asked by: Richard C

0

Expert Reply:

We do not have any replacement parts for the Atwood 61101 brake actuator. I do have a direct replacement. The Demco Hydraulic Brake Actuator - Drum - Zinc - 2" Ball - 7,000 lbs, part # DM72VR, is a bolt-on brake actuator that mounts on 3" centers.

I have included a product description link and a video demo link below.

expert reply by: Mark Smith

0

Answer 1

Assuming you have drum brakes, the Demco Hydraulic Brake Actuator - Drum - Zinc - 2" Ball - 7,000 lbs #DM72VR will work well as a replacement for your Atwood 61101. If you have disc brakes, I recommend the Dexter #099-175-20 which comes with an…

view full answer...

Answer 2

The Demco 8605001 was discontinued so for a very similar option we have the Demco #DM72VR which is for drum brakes, fits a 2 inch ball, and has a 7k capacity.

view full answer...

Answer 3

The Atwood 85778 actuator has been discontinued so I recommend the Dexter DX7.5L A-60 Brake Actuator - Bolt On - Drum - 2" Ball - Zinc - 7,500 lbs #DX33FR. If you need a higher capacity, then you will need to use a 2-5/16 inch hitch ball.…

view full answer...

Answer 4

I can understand how this can be a bit confusing. Brake actuators, like the Demco Hydraulic Trailer Brake Actuator, #DM72VR, with no lock-out are typically more economical and are perfect for trailers equipped with free-backing brakes because the…

view full answer...

Answer 5

The best recommendation I can give you since we don't carry the Gabriel actuators would be to check out the link I attached that will take you to a page that has all of the actuator shocks we carry. On the product pages for each there will be…

view full answer...

Answer 6

If you look under the coupler #DM72VR you will see what looks like a nut on the latch assembly with a spring behind it. I attached a picture that points it out. Loosen it slightly until the ball fits in the coupler and latches properly.

view full answer...

Answer 7

The Demco Hydraulic Brake Actuator DM8608601 you were looking at requires 1/2" x 4-1/2" Grade 5 Bolts to mount it to the tongue of your trailer. The DM8608601 was actually discontinued recently so I recommend going with the Demco Hydraulic…

view full answer...

Answer 8

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 12

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...