What Axles Sizes Work with the Timbren Silent Ride Suspension for Tandem Axle Trailers - 7,000 Lbs

Question

Question:

Is Timbren silent ride compatible with 7000k 4inch axles? respectfully,

asked by: Brent W

0

Expert Reply:

The Timbren Silent Ride Suspension for Tandem Axle Trailers - 7,000 Lbs is only available for 3" round axles part # TSR7000T05 or 2" square part # T43FR. The vast majority of 7K trailer axles will be 3" round.

expert reply by: Conner L

0

Answer 1

The Timbren Rear Suspension Enhancement System part #TGMRTT35S is a great option for a 2005 GMC Sierra 3500 with truck bed camper. They are actually designed for constant loads like this so they will provide excellent support. They are also…

view full answer...

Answer 2

Personally I prefer the Demco Trailer Coupler #DM14976-52 with the composite handle over the Coupler #DM15791-81 with a metal handle. I feel it is easier to operate as it does not have the safety latch like you get on the metal handle. Since most…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 9

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 10

Hey Jaime, yes you can replace your 25-1/4 inch 3,500 lb axle leaf springs with a 5k rated axle spring like the part #e44SR. This will increase the suspension's weight capacity and might make the ride quality a little rougher but it would fit and…

view full answer...

Answer 11

Roadmasters priority when it comes to their sway bars is top notch quality and the easiest install for the customer. This typically cuts the install time down enough that you end up saving money if you pay to have the bars installed or decide to do…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...