Replacement Landing Gear Legs for Venture Landing Gear

Question

Question:

Can I replace the passenger side leg of the landing gear or will I have to replace the entire landing gear set? I can find the replacement gear box. Mine is fine but IS 19 years old. the sheared post on the passengers side has me sitting still until I replace.

asked by: Mark W

0

Expert Reply:

Thanks for the pictures. You won't need to replace the entire landing gear set. For your Venture landing gear on your 2002 Forest River Cedar Creek Fifth Wheel you will want item # LC119102 for the lead leg or item # LC119101 for the follow leg.

The Replacement Gearbox for Venture Aluminum Electric 5th Wheel RV Landing Gear Assemblies item # LC276602 you were looking at is the correct gear box.

expert reply by: Jerred H

0

customer pic broken drive
(click to enlarge)

venture landing gear
(click to enlarge)

Answer 1

Yes, based on the picture you sent in the replacement gearbox part #LC276602 that you referenced is the correct replacement. This is aluminum too which means it will be a bit stronger as well.

view full answer...

Answer 2

Yes, for your Venture VMC900R lead leg jack the part #LC146059 is the correct repair kit.

view full answer...

Answer 3

I recommend the Lippert Venture 5th Wheel RV Landing Gear Motor part #LC142178. This motor is designed to work with the Replacement Gearbox for Venture Aluminum Electric 5th Wheel RV Landing Gear Assemblies, part #LC276602. It has a rated load of…

view full answer...

Answer 4

Yes, I attached a diagram you can use to install the #LC146059 that you referenced.

view full answer...

Answer 5

You could re-use your existing #LG-4 if you have that bottom attachment bracket relocated to the appropriate position. It would involve removing the existing bracket and having the bracket provided with the #LG-4 welded into place. If you'd…

view full answer...

Answer 6

We have a couple options for the Lippert replacement follow landing gear leg for your 2005 Thor Tahoe Transport 27WTB. To ensure you get the correct leg you will need to measure the length of your outer black portion of the leg. The Replacement…

view full answer...

Answer 7

The correct replacement landing gear box for a Venture Landing Gear System is the Replacement Gearbox for Venture Aluminum Electric 5th Wheel RV Landing Gear Assemblies part #LC276602.

view full answer...

Answer 8

To determine the correct landing gear you need you'll need to measure the mounting brackets you have on your trailer. If they measure 17-1/2 inches from outside to outside then our most popular landing gear for you is the etrailer set, part…

view full answer...

Answer 9

The replacement motor for your Lippert Venture VMC940RB would be the Replacement Motor for Stromberg Carlson Electric Landing Gear Set #LC196308. The Replacement Gearbox #LC276602 is correct too if you needed that as well.

view full answer...

Answer 10

First thing I'd check is the power source and ground for the landing gear. What you described could be a bad motor, but a weak battery or ground will cause the same problem. Your picture is pretty close up, but it looks like the motor you'd…

view full answer...

Answer 11

Good news! I was able to go out to the warehouse and measure the etrailer landing gear #RVLG-8HDL for you. I found that the distance between the weld stops from the outside to outside is 17-1/2 inches and from the inside to the inside of the weld…

view full answer...

Answer 12

Your Keystone Raptor Camper would have had Venture type landing gear on it so for a set of powered landing gear that would fit without modification you would want the Lippert part #LC333964. This has a 6k lifting strength so it would be more than…

view full answer...

Replacement Landing Gear Legs for Venture Landing Gear

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching