Flow Thru Sensor Tire Pressure System for Trailer that Can be Left On During Storage

Question

Question:

I like the flow through sensors. Do you recommend metal valve stems for these? Do you recommend removal of the sensors during winter storage?

asked by: Robert M

0

Expert Reply:

For a tire pressure monitoring system that has 4 flow thru sensors we have the TireMinder A1AS TPMS for RVs and Trailers # TM76FR which would work really well. These can be left on during storage without issue as well.

expert reply by: Jameson C

0

Answer 1

Yes, there are solutions for running tire pressure sensors with the rubber valve stems on your Lionshead Aluminum Jaguar Trailer Wheel item #LHSJ211G. The TST TPMS for RVs - Color Display - Signal Booster - 4 Tire Sensors item #TST-507-RV-4-C are…

view full answer...

Answer 2

The bearing races on a trailer hub, like the Trailer Hub Assembly, part #8-258-5UC1, are removable, they are not built into the hub. I am including a link to a FAQ page on wheel bearings, races, and seals. Also, a link to a video of removing and…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Good morning, Cliff. As of today (3/27/24) we are expecting the #KE33JR tire/wheel combo to be in stock in about 2 weeks. Hopefully this means we can take our own pictures and put them on the site within maybe about 3-4 weeks from now. What I can…

view full answer...

Answer 6

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 12

I spoke to Dexter and they said there is a bit of a process for installing the spindle nut properly. 1. You will need to thread on the inner nut, rotate the hub, then tighten the nut to 100 foot pounds. 2. Loosen the nut to remove the torque, making…

view full answer...