Trailer Foot that Fits Trailer Jack # TJA-5000S-B

Question

Question:

Does trailer jack part number TJA-5000S-B work with adjustable leg number JF-99?

asked by: Jeremy S

0

Expert Reply:

The # JF-99 fit your etrailer.com trailer jack # TJA-5000S-B.

expert reply by: Jameson C

0

Answer 1

You should add grease 3 or 4 times a year to your #TJA-5000S-B, but really it depends on several factors like how often the jack is used, how long it sits, the climate, and so on. It should take about 3 or 4 pumps of grease from a grease gun. You…

view full answer...

Answer 2

We have several jacks here that should work well on your camper. The etrailer A-Frame jack part #TJA-5000S-B that you referenced would be a great choice for if you are looking for an A-frame style jack with a higher capacity.

view full answer...

Answer 3

Yes, the Drop Leg for etrailer and Ram Jacks - 13-1/4" Tall - 5-1/4" Diameter Footplate - Zinc #JF-1005H-Z that you referenced will work with the Round A-Frame Trailer Jack - Sidewind - 15-5/8" Travel - 5,000 lbs #TJA-5000S-B. Check…

view full answer...

Answer 4

I ran out to our warehouse and pulled one of the etrailer trailer jacks #TJA-5000S-B jacks off the shelf. I measured the retracted height of the jack at 23-3/8 inches and found the outer tube to be 2-1/4 inches in diameter.

view full answer...

Answer 5

The majority of sewer hoses won't fit inside a standard 4" RV rear bumper because the molded-on ends which contains the lug and bayonet fittings are too large. However, if you were to go with an option that doesn't have the molded-on…

view full answer...

Answer 6

The drop leg #JF-1005H-Z fits 2,000 pound etrailer and Ram jacks as well as topwind 5,000 pound jacks, like part #TJA-5000-B but it doesn't fit the 5,000 pound sidewind jacks like #TJA-5000S-B. The inner tube on the 5k sidewind jacks have a…

view full answer...

Answer 7

The Round A-Frame Trailer Jack #TJA-5000S-B has mounting holes that are elongated. The actual holes are 3/4 inch long and 7/16 inch wide. That gives you a minimum of 2-1/2 inches or maximum of 3-3/4 inches to the nearest or farthest part for…

view full answer...

Answer 8

I just went out to the warehouse and checked. The Drop Leg for etrailer and Ram Jacks Footplate item #JF-1005H-Z fits perfectly with the etrailer A-Frame Round Jack item #TJA-5000S-B.

view full answer...

Answer 9

If you are looking to maximize the capacity of the etrailer.com 5,000-pound Jack #TJA-5000S-B, you are not limited to the 2,000-pound drop legs. With that said, you will want to check out the etrailer.com #JF-1005H-Z drop leg. This is rated up to…

view full answer...

Answer 10

For your 10,000 lb car hauler trailer, I recommend the Round A-Frame Trailer Jack - Sidewind - 15-5/8" Travel - 5,000 lbs #TJA-5000S-B for a manual jack, with footplate #JF-99. The majority of the weight of your trailer will be on your axles and…

view full answer...

Answer 11

Thanks for the picture of your jack. From that I can tell that you have the Round A-Frame Trailer Jack #TJA-2002-B and the correct replacement foot you'll need is the #JF-1005H-Z that you mentioned. This will give you up to an additional 8 inches…

view full answer...

Answer 12

Though these two jacks do look to be nearly identical, there is one fairly large difference, and one lesser of one as well. The large one being the weight capacities they can handle. The #HD50000101 is rated up to 5,000 pounds, whereas the…

view full answer...