Does etrailer Drop Leg Fit 5,000 Pound Sidewind Jack

Question

Question:

will this leg fit jack TJA-5000S-B?

asked by: Hal

0

Expert Reply:

The drop leg # JF-1005H-Z fits 2,000 pound etrailer and Ram jacks as well as topwind 5,000 pound jacks, like part # TJA-5000-B but it doesn't fit the 5,000 pound sidewind jacks like # TJA-5000S-B.

The inner tube on the 5k sidewind jacks have a thicker inner tube that doesn't allow the leg to slide up inside.

expert reply by: Charles S

0

Answer 1

The Round A-Frame Trailer Jack #TJA-5000S-B has mounting holes that are elongated. The actual holes are 3/4 inch long and 7/16 inch wide. That gives you a minimum of 2-1/2 inches or maximum of 3-3/4 inches to the nearest or farthest part for…

view full answer...

Answer 2

All of the side mount jacks that we carry either come with a welded footplate or welded wheel. Though the tubing size is 2 inches, I cannot recommend modifying jack #DL22300, or any jack with a wheel or footplate welded on, as it will void the…

view full answer...

Answer 3

The Round A-Frame Trailer Jack #TJA-5000-B you were looking at does not have grease zerks, nor is it greaseable. This is the same for all of the top wind A-Frame jacks we offer. The reason for this is A-Frame jacks like this are sealed to keep debris…

view full answer...

Answer 4

For the etrailer a-frame jack part #TJA-5000-B we have the detachable foot plate part #JF-99 as one option or we have a caster wheel part #JC-102 as another option!

view full answer...

Answer 5

Yes, the Drop Leg for etrailer and Ram Jacks - 13-1/4" Tall - 5-1/4" Diameter Footplate - Zinc #JF-1005H-Z that you referenced will work with the Round A-Frame Trailer Jack - Sidewind - 15-5/8" Travel - 5,000 lbs #TJA-5000S-B. Check…

view full answer...

Answer 6

I ran out to our warehouse and pulled one of the etrailer trailer jacks #TJA-5000S-B jacks off the shelf. I measured the retracted height of the jack at 23-3/8 inches and found the outer tube to be 2-1/4 inches in diameter.

view full answer...

Answer 7

We have several jacks here that should work well on your camper. The etrailer A-Frame jack part #TJA-5000S-B that you referenced would be a great choice for if you are looking for an A-frame style jack with a higher capacity.

view full answer...

Answer 8

You should add grease 3 or 4 times a year to your #TJA-5000S-B, but really it depends on several factors like how often the jack is used, how long it sits, the climate, and so on. It should take about 3 or 4 pumps of grease from a grease gun. You…

view full answer...

Answer 9

The #JF-99 fit your etrailer.com trailer jack #TJA-5000S-B.

view full answer...

Answer 10

If you look at the backs of the brake assemblies there should be a hole where the magnet wires come out and a little opaque plastic strap. So if you are looking at the back of the assembly and those items are on the left then it is the left side…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Does etrailer Drop Leg Fit 5,000 Pound Sidewind Jack

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching