Can a Bolt-On Swivel Jack be Mounted to the Same Bracket as a Weld-On Trailer Jack

Question

Question:

I have a broken Fulton Bolt-Thru Swivel Marine Jack - Weld On and was wondering if the Fulton Bolt-Thru Swivel Marine Jack with Dual Wheels - Sidewind - 12inch Lift - 1,500 lbs can be mounted on the existing weld-on plate?

asked by: Jim W

0

Expert Reply:

You would need to replace the weld-on jack with another weld-on jack of the same type. The bolt on jacks have a different mounting bracket than the weld-on ones. You could use # FXP15W and you may also need bracket # P9012-00 if the old one turns out to not be compatible.

expert reply by: Michael H

0

Answer 1

For the bolt-on or weld-on bracket to fully install the Bulldog Round Bolt-Thru Swivel Jack #BD154102 to your trailer, you will use the Jack Mounting Bracket #P9012-00. This can be either bolted to or welded on your trailer frame for use with the…

view full answer...

Answer 2

The Fulton Bolt-Thru Swivel Marine Jack #F1411300301 will definitely work for you as a replacement for the current Fulton Magnum Series jack you have, as it will mount to the bracket already on your trailer, as that bracket will be the Jack…

view full answer...

Answer 3

If you wanted to use the Fulton #FXPD15L jack in place of your old welded on unit, you would first need to cut the old weld on bracket off of your trailer. Once you've done that, you can switch to a bolt on style trailer jack. You won't be…

view full answer...

Answer 4

I'm not sure if you are asking the weight capacity or weight of the Fulton Bolt-Thru Swivel Marine Jack with Dual Wheels #FXPD15L so I'll go ahead and give you both just to cover our bases. This jack has a lift capacity of 1,500 lbs (which…

view full answer...

Answer 5

Having 2 wheels will provide more surface area/contact with the ground. This could actually make it more difficult to maneuver compared to a single wheel. But two wheels are better than one when not on pavement. A single wheel tends to dig into dirt…

view full answer...

Answer 6

Typically the tongue weight and the height needed to clear the towing vehicle coupler are the considering factors for choosing an appropriate trailer jack. It is recommended to choose the jack has a higher capacity than the tongue weight of your…

view full answer...

Answer 7

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 8

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 9

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 10

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 11

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 12

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...