Solution To Go From A 1-1/2 Inch Hose Fitting To A 3 Inch Bayonet Fitting

Question

Question:

I need a bayonet fitting for rv black tank outlet to a 1.5” hose fitting. It will be connecting to a portable macerator. Do u have this product?

asked by: Natalie M

1

Helpful Expert Reply:

We have the LaSalle # 34466V153 which will slide on over your 1-1/2" pipe to give you 3" pipe. From here you can use # T1028 to give you the bayonet fitting you're needing.

Use the solvent cement # 3447530889 to complete installation and prevent leaks.

expert reply by: Bryce D

1

Answer 1

We have the LaSalle Bristol Eccentric Tank Reducer #34466V153 which can slide over your 1-1/2 inch diameter gray pipe to give you a 3 inch pipe that you could then attach the 3 inch pipe to 3 inch bayonet adapter part #T1028 and you'd be set.

view full answer...

Answer 2

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 3

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 4

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 5

According to my research, your 92865A-1 hub/drum has a 25580 inner and an 14125A outer bearing and a 8 on 6-1/2 inch lug pattern, as does the AxleTek #AKHD-865-7-2-K hub drum you referenced. The #AKHD-865-7-2-K would be an acceptable replacement for…

view full answer...

Answer 6

I do have an option but Glo-Brite is no longer in business so you won't be able to get any replacement parts for these lights such as lenses. The only option you have would be a full replacement for which the most similar option we offer is the…

view full answer...

Answer 7

We have toppers that'll work for 2 of your 3 sliders. For your 12 foot 9-1/2 slide, use #LCV000168109 which is designed for slides measuring between 152-157 inches wide. The longest topper we offer is for slides 188-193-3/4 inches, so…

view full answer...

Answer 8

If you check out the picture I attached you can see that the roller and slide out awning assembly of the Solera RV Slide-Out Awning #LCV000435661 actually will sit below the awning rail so your setup having a tight clearance between the rail and the…

view full answer...

Answer 9

I recommend to use the Solera 16-1/2' Slider part #LCV000435661 which matches the boxes width exactly so you will not have side overhang like we normally recommend but it is the biggest slide topper available to fit the 198" width of your…

view full answer...

Answer 10

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 11

Please note the attached instructions. The Lippert Anti-Billowing Kit for Solera Slide Topper Awnings, #LC78FR should be installed on the end of the awning that is closest to the front of the unit. 1. Make sure awning is fully retracted. 2. Place the…

view full answer...

Answer 12

The Champion 9,000-Watt Dual Fuel Inverter Generators w/ Parallel Kit, #CH49FR has the same power output specs regardless of type fuel used. There is a starting (surge) power output of 4,500 watts/37.50 amps with a running power output of 3,500…

view full answer...