Trailer Hitch For A 2021 Mazda MX-5 Miata

Question

Question:

I need a trailer hitch for my 2021 Mazda MX-5 miata

asked by: Pedro

0

Expert Reply:

For your 2021 Mazda MX-5 Miata, we have the Curt Trailer Hitch # C11435. This is a class I trailer hitch, that has a maximum towing weight of 2,000lbs, and a max tongue weight of 200lbs.

If you're needing wiring, we have the Curt T-Connector # C56300. This is an easy to install, plug-and-play harness that will plug into your vehicle's factory wiring harness. Wiring is needed to be able to provide lights to your trailer while driving, that was you're compliant with the law and for safety.

Finally, you may need a ball mount to complete your setup. If so, I recommend the Reese Trailer Hitch Starter Ball Mount Kit # RP7043000. This kit comes with a ball mount that has 3/4" of rise, and 1-1/4" of drop, a hitch pin and clip, and a 2" ball.

expert reply by: Bryce D

0

Answer 1

We do have an option for your 2021 Mazda MX-5 Miata, the Curt Trailer Hitch Receiver #C11435. This hitch is a class I trailer hitch that is capable of 2,000lbs GTW and 200lbs maximum tongue weight. You'll want to check your vehicle's…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

The Curt Trailer Hitch Receiver #C11435 referenced in your question is a Class I trailer hitch and is confirmed to fit your 2016 Mazda MX-5 Miata. The hitch will always be somewhat visible when looking at your vehicle from behind, whether or not it…

view full answer...

Answer 7

Yes, the Curt hitch part #C11435 is a confirmed fit for your 2016 Mazda MX-5 Miata and would have enough capacity for pulling a jetski trailer. It has a 2,000 lb capacity which would be more than enough. For trailer wiring you'd then need the…

view full answer...

Answer 8

The Curt hitch part #C11435 is the correct fit for your 2016 Mazda MX-5 and would be the way to go for carrying a cargo carrier like the #C18145. We don't have an aluminum carrier that fits this hitch size but the #C18145 only weighs 29 lbs.

view full answer...

Answer 9

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 10

I do have a solution for you, however the closest spacer block we currently have available to the dimensions you listed in your question is the Reese Spacer Block #RP3022. The size of this spacer block is 1/4" x 1" x 3". If you are…

view full answer...

Answer 11

The Swagman XTC-2 2-Bike Platform Rack part #S64670 weighs right around 33 lbs. This will actually be one of the lightest platform style bike racks we offer. It has a 3" raised shank which will help with ground clearance and it can be folded…

view full answer...

Answer 12

I don't have a precise ground clearance measurement for the Curt Class I #C11435 (nor does Curt), but as you can see in the provided photo, the receiver tube will sit flush against the underside of the bumper fascia. If you measure approximately…

view full answer...