2 Inch Wide Replacement Equalizer for Slipper Springs on Seven Thousand Pound Triple Axle Trailer
Question:
My trailer has three, seven thousand pound axles. I need to replace, or rebush, the equalizers. The equalizers are the fabricated type. Dimensions as below: A = 13-13/16 B = 5-3/4 C = 5-15/16 D = 9/16 E = 7/8 F = 3/8 Inside dimension between sides = 2-3/16 Outside dimension side to side = 2-3/4 I need four new equalizers - Do you have something that will work? If not, I will cut out the old bushings, fabricate and weld-in new bushings.
asked by: Allan M
Expert Reply:
The TruRyde # TREQ1344 Equalizer for 2 inch wide Slipper Springs that you referenced is considered a fit for the dimensions that you listed on your triple axle trailer with seven thousand pound axles. I would recommend replacing the entire equalizer instead of welding in new bushings. You indeed would need 4 equalizers for your triple axle trailer.
The total length (a) and the length from the center of the front bolt hole to the center of the middle bolt hole (b) is slightly off when compared to your measurements but since you are using slipper springs this will work. The slight difference in the measurements will shift the resting position on the open end of the slipper spring.
Since you are replacing the entire equalizers, I recommend replacing the hardware to hold this equalizer in place as well. The Redline Spring Eye Bolt # 166079 would work for your application. I have provided a link to this product as well as a helpful article regarding slipper springs for your reference.
Products Referenced in This Question
Spring-Eye Bolt with Locknut for Slipper Springs - 3-1/2" Long
- Trailer Suspension Parts
- Suspension Bolts
- Camper
- Car Hauler
- Utility Trailer
- 9/16 Inch Diameter
- 3-1/2 Inch Long
- ABS Fasteners
more information >
Product Page this Question was Asked From
Equalizer for 2" Wide Slipper Springs - 13-1/8" Long - 7/8" Center Hole
- Trailer Suspension Parts
- Standard Equalizer
- Camper
- Car Hauler
- Utility Trailer
- Slipper Springs - 2 Inch
- 13-1/8 Inch Long
- Tandem Axle
- Triple Axle
- TruRyde
more information >
Continue Researching
- Shop: Spring-Eye Bolt with Locknut for Slipper Springs - 3-1/2" Long
- Shop: Nylon Bushing - 9/16" Inner Diameter, 11/16" Outer Diameter - 2" Long
- Shop: Equalizer Bolt with Cotter Pin and Castle Nut - 7/8" Diameter
- Shop: Equalizer Suspension Bolt with Locknut - 5-1/4" Long
- Shop: Wet Equalizer Bolt with Locknut and Grease Zerk for Double-Eye Springs - 3" Long
- Shop: Hopkins 7-Way Molded Trailer Wire Connector - 11' Long
- Shop: Shackle Bolt with Locknut for Double-Eye Springs - 3" Long
- Q&A: Replacement Slipper Leaf Spring for Triton PWC Trailer
- Video: Hopkins 7 Way Molded Trailer WIre Connector Review
- Q&A: Parts Needed to Convert Triple Axle Trailer with Drum Brakes to Electric Over Hydraulic
- Q&A: How to Bleed Electric Over Hydraulic Trailer Brakes
- Video: HydraStar Hydraulic Brake Line Kit Review
- Q&A: Grease Cap Recommendation for Hub Bore of 1.96 inch
- Q&A: Replacement Hub and Brake Assembly for AL-KO 8490
- Q&A: Replacement Brake Magnets, Bearings and Seals for Al-Ko 3500-lb 8490 Hubs
- Search Results: bearing and seal kits
- Search Results: seal
- Video: TruRyde Trailer Suspension TRFA71063 Review
- Video: Redline Trailer Suspension 516-25TB Review
- Video: TruRyde Trailer Suspension - Leaf Spring Suspension - TREQ1304 Review
- Video: Review of Trailer Leaf Spring Suspension - Spring Mounting Hardware - 166079
- Video: Review of Redline Trailer Leaf Spring Suspension - Equalizers - AP216
- Search Results: slipper spring equalizer
- Search Results: 1403t3
- Search Results: slipper springs
- Article: Breakaway Kit Installation for Single and Dual Brake Axle Trailers
- Q&A: Closest Metric Replacement Tire Size for 7.00-15 Tire on Livestock Trailer
- Article: Slipper Spring Trailer Suspension System Review
- Article: Where to Position the Trailer Axle?
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)