Trailer Brakes Lock Up When Using the Tekonsah Primus IQ Brake Controller on a 1996 Ford F-350

Question

Question:

I have a 1996 Ford F350 with the 7.3L diesel. I have the Tekonsha Primus IQ with boost button. I am pulling a 1996 Wilderness 27N travel trailer. The problem that Im having is when I hook up my trailer to the truck this is the first time Ive used the Primus IQ...just bought the truck and it came with it, all of my lights are there, etc. However, when I begin to pull the trailer so I can calibrate the controller, I go about 2 feet and the trailer brakes lock and I stop. I can go forward and backward about 2 feet before the trailer locks up and Im just sitting there. Obviously, if I disconnect the trailer plug, I can pull the trailer wherever without lights, brakes, etc. though. Any ideas? Is the controller not speaking to my trailer the way that it would like? Am I missing a step in setting everything up? Let me know. Were supposed to go camping in a couple of days, but Im a sitting duck without my trailer brakes or lights, etc.. Let me know if there are follow-up questions that I havent answered that may be useful. Thanks so much!

asked by: Destin

1

Helpful Expert Reply:

It sounds to me like there is either a wiring issue between the brake controller and the trailer connector on the truck or the brake controller is bad. Since your trailer brakes lock up when you are connected to the truck, that would indicate that there is constant power on the brake output circuit.

The first step that I would take is to use a circuit tester with an incandescent bulb like our # PTW2993 to test the pin in the 5 o'clock position if you have a 7-way trailer connector. If you have a 6-way trailer connector, then the brake output circuit may be either on the center pin or on the pin in the 10 o'clock position. You may want to have the truck running to ensure there is full voltage on all circuits. If you have constant power on the 5 o'clock pin on the 7-way connector, then move to the brake controller.

For the 6-way connector, there are two common ways to wire a 6-way trailer connector. The differences are the pin locations for 12-volt power and the electric brakes. Make sure your trailer 6-way connector is wired the same way as the 6-way connector on your truck.

Moving to the brake controller, the Primus IQ should have 4 wires coming out of the back. White for ground, black for 12-volt power from the battery, blue for brake output to the trailer and the red wire should be connected to the cold side of the brake switch. Cut the blue wire about 6 inches back from the brake controller and test the wire with the circuit tester. If there is constant power on the blue wire, then the brake controller may be bad. If there is no power, then make sure the brake controller is wired correctly.

You should have constant 12-volt power on the black wire and the red wire should only show power when you step on the brake pedal.

If the brake controller is wired correctly and you still have constant power at the 5 oclock pin on your truck, it may be possible that the trailer connector on your truck was wired incorrectly. The connector on your trailer could also be wired incorrectly. I have attached a photo showing the functions of each pin on a 7-way connector for you to compare to your trailer connectors.

Trailer connector adapters can also cause similar problems, especially if you are converting a 7-way connector to a 6-way. With the adapter plugged in, make sure the brake output pin on the 6-way side matchup between the adapter and the connector on the truck or trailer.

I have attached three FAQ articles on brake controller installation and troubleshooting for you to check out. If you are unable to find a solution or the problem after following these steps, let me know what you come up with and we can take further steps.

expert reply by: John H

1

click to enlarge

Answer 1

The correct anode rod for your Suburban Water Heater SW6DELC is the Camco RV Water Heater Anode Rod #CAM11563 which has a 3/4" diameter and is 9-1/2" long. Attached is a review video of this anode rod as well as a video on how to clean and…

view full answer...

Answer 2

Since your trailer has the bracket #FRCBRKT-BL that would mean your trailer has the Furrion pre-wiring which is very common for newer RVs. The part #FOS43TASF is a fit for this and would be a really easy install. This gives you a monitor with a 4.3…

view full answer...

Answer 3

You can have more than one iPhone "connected" to the Lippert Tire Linc system part #LC37VR but only one can be used at a time. So basically you or your wife could have their phone connected but if you needed to switch between the two phones…

view full answer...

Answer 4

The Furrion camera system we have is a closed system and would not be compatible with the in-dash display so you would need to purchase GM's camera system to be able to connect to your display instead of having another monitor. If you do end up…

view full answer...

Answer 5

Demco actually has a kit that was designed to convert an Air Force One kit to a Stay in Play DUO which is what you would need since you have hydraulic brakes with the part #SM99231. This will work with what you have now and work great. If you send me…

view full answer...

Answer 6

The newer Chevrolet and GM pickup trucks have a known power deficiency issue with the Furrion Vision S Wireless RV Observation Camera System w/ Side Marker Light Cameras #FCE48TASL-05. There is likely nothing wrong that you did, the problem is the…

view full answer...

Answer 7

We have 2 different remotes available for HappiJac electric camper jack systems. - Replacement Remote Control for HappiJac Electric Camper Jack Systems #LC723915 - Replacement Remote Controller for Wireless HappiJac Electric Truck Camper Jacks…

view full answer...

Answer 8

There is a wireless camera you can use for your travel trailer that will always be on. It is the Furrion Vision S Wireless RV Backup Camera System w/ Night Vision item #FOS05TASF. It comes with a 5" monitor and you will want to wire the camera…

view full answer...