What Hitch Receiver Do You Recommend For My 2022 Toyota Sienna

Question

Question:

What 2" hitch receiver do you recommend for my 2021 Toyota Sienna?

asked by: Mick

0

Expert Reply:

My hitch receiver recommendation for your 2022 Toyota Sienna is the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2", part # C22UR. It has a maximum tongue weight of 350 lbs and a maximum gross trailer weight of 3,500 lbs. It comes with a gloss power coated finish to resist rust and corrosion. The installation is bolt on, no welding required.

I also recommend that you get your vehicle ready to tow by adding the necessary wiring. Adding the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector, part # TK69FR, provides you with a custom wiring kit that sets you up to tow utility trailers. This wiring will allow your trailer to mirror your brake lights, turn signals, and running lights.

I have included product description links and a demo video below.

expert reply by: Mark Smith

0

Answer 1

You do need to make a direct wired battery connection for a powered wiring harness like #118498 because the small accessory 12V convenience outlets provided in vehicle do not have a high enough current rating to power the harness and all of the…

view full answer...

Answer 2

For your 2012 Toyota Sienna Tow Ready wiring harness #118498 will establish the 4-Way like you said. You can use #30717 as a 4 to 7-Way adapter but I recommend #37185 because it will give you both a 7-Way and still retain the 4-Way. The white wire…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 10

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 11

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

What Hitch Receiver Do You Recommend For My 2022 Toyota Sienna

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching