What is Causing My UltraGroove Tonneau Cover to Slip on My Truck?

Question

Question:

right side gearnot motor side not grabbing cover. slipping

asked by: Joe

0

Expert Reply:

There are two things to consider for troubleshooting any resistance/slipping while opening the Pace Edwards UltraGroove # 311-KMC95A17. First off, you need to make sure that the actuator nob is turned clockwise a full 90 degrees (until it clicks) in order for the handle latches to fully retract. I went ahead and attached a picture of the latches opened and closed to show you what they look like in both positions.

Another thing that could be causing the slipping is making sure the sweep seals on are properly lubricated. The UltraGroove comes with a 303 brand protectant sponge pack for you to use with this purpose. I went ahead and attached a photo from the instructional manual that walks you through the process.

If you are still experiencing slipping/resistance of your cover, feel free to respond to this response and I will be happy to assist you further.

expert reply by: Bob C

0

Pace Edwards UlltraGroove # 311-KMC95A17
(click to enlarge)

Lubricating the Sweep Seals on the Pace-Edwards UltraGroove
(click to enlarge)

Answer 1

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 2

A drop axle certainly can make it tough to reach the star wheel adjuster on a drum brake. The adjuster spoon tool we offer #W80630 has a 90-degree bend that will often let you get access to the adjuster even on a drop axle. Essentially you will need…

view full answer...

Answer 3

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 4

The Tekonsha OEM Vehicle Wiring Harness #22121 that you referenced includes all the wiring and parts necessary to install a fully functional 7-Way connector and trailer brake controller. The included brake controller harness is compatible with and…

view full answer...

Answer 5

From the looks of the photo you sent it does not look like you have an OEM suspension system on your boat trailer. I recommend securing the suspension rail to the trailer frame in a more secure manner like drilling and using bolts so that it does not…

view full answer...

Answer 6

We do have a compatible grease seal for your 168255TC oil seal, however, we do not carry rubber coated seals in this size. The 168255TC oil seal was designed to work with oil bath hubs on a 3,500 lb axle. For the most part, axle manufacturers have…

view full answer...

Answer 7

Thanks for submitting the picture of the lights you are looking for. Based on that it looks like you are in need of a 194 bulb like the part #A194B.

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

For your 4x6 utility trailer, I recommend using the Taskmaster 4.80R12 Radial Trailer Tire part #TT48012C. This tire has a radial ply construction which will be better for the longer highway trips you intended to make. It has a load range C rating…

view full answer...

Answer 10

The different size Equal-I-Zer systems have heads to match the bar sizes so the parts are not interchangeable. But not to worry, with some adjustment you can soften it up a little and not have to use a different system. You will need to lower the…

view full answer...

Answer 11

If the light mounting surface on your older Prowler trailer is not flat enough to allow for use of caulk for sealing the rear of the RV Tail Light #30-92-001 then you might want to use a weather strip tape like #WS1412 which is 1/4-inch thick x…

view full answer...

Answer 12

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

What is Causing My UltraGroove Tonneau Cover to Slip on My Truck?

Product Page this Question was Asked From

Continue Researching