Stallion Aluminum Car Hauler Ramp Set for Twin Axle Trailer

Question

Question:

looking for ramps for twin axle trailer. Ramps need to be at least 6000lbs capacity

asked by: William D

1

Helpful Expert Reply:

The Stallion Aluminum Car Hauler Ramp Set item # 288-07502 you were looking at would be the perfect fit for your twin axle trailer. These ramps combined have a 6,000 lbs capacity and only weigh 20 lbs per ramp. They are 5' long x 14-1/2" wide x 3-3/4" thick and will work on a trailer up to 16" off the ground.

expert reply by: Jerred H

1

Answer 1

The height restriction on ramp set #288-07502 has to do with the distribution of the weight, ability for tires to grip, and clearance between the tops of the ramps and the vehicle rolling up them. The shorter the ramp the more severe the angle will…

view full answer...

Answer 2

The handles for the Aluminum Car Hauler Ramp Set #288-07502 are welded on to the ramp. They will need to be cut off if they will not fit into your area with the handles attached. The ramps will still be able to be carried by the lips of the ramp as…

view full answer...

Answer 3

The measurement on the Aluminum Car Hauler Ramp Set part #288-07502 does not include the handle. They are 14.5" outside of ramp to outside of ramp. There is an additional 1.5" of width in the handle area getting to 16". The handles can…

view full answer...

Answer 4

I attached a picture that shows what the end of the Gen-Y Hitch Aluminum Loading Ramps #325-GH-R84 looks like. It's a hook style that grabs the trailer so it doesn't slide off.

view full answer...

Answer 5

We have the Draw Tite part #24943 which fits the diesel and non-diesel sedans and then if you have a hatch we have the part #C11458 which is a confirmed fit.

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

I am sorry I don't have any tires that are going to fit your rim. I do have a couple of comparable size tires that come in a wheel tire combo. I have listed the two below along with their lug patterns. 5 on 4-1/2 Lug Pattern - Kenda 205/65-10…

view full answer...

Answer 11

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Stallion Aluminum Car Hauler Ramp Set for Twin Axle Trailer

Featured Help Information

Miscellaneous Media

Continue Researching