How is Different Gears Selected on Bulldog 2-Speed Jack # BD183401

Question

Question:

Been trying to do some research with no luck. Looking for the operation of the two speed planetary gearbox more specifically how do you change between high and low gears.

asked by: Matt B

0

Expert Reply:

To change gears on the Bulldog 2-Speed Jack # BD183401 that you referenced you would push in/pull out on the shaft. This is how you go between the two speeds.

expert reply by: Jameson C

0

Answer 1

I contacted our representative at Bulldog, the item you selected, Bulldog Trailer Jack, part #BD183902, would be the correct jack you are looking for. The Bulldog Jack #BD183902 is a 10,000 lb capacity, spring loaded, 2 speed jack that is welded to…

view full answer...

Answer 2

When choosing a jack for your trailer you will want to remember that the jack is not going to be lifting the entire weight of the trailer. You should choose a jack that exceeds the tongue weight of your trailer when it is fully loaded. The tongue…

view full answer...

Answer 3

The differences between the two jacks is minimal. The main feature difference is that the Bulldog #BD178203 has the ASABE (American Society of Agricultural and Biological Engineers) compliancy certification whereas the ProSeries #PS1401440303 does…

view full answer...

Answer 4

The Sundowner 2 horse trailers usually use a weld on square jack. To replace it I recommend the Bulldog Square Jack #BD182304. If you wanted to add a motor to this style of jack, I recommend the Bulldog Powered-Drive Kit for Single-Speed Jacks…

view full answer...

Answer 5

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 6

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 7

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 8

Below is the general process for bleeding an electric over hydraulic brake actuator like #K71-650. Fill reservoir with NEW brake fluid. Never re-use brake fluid that has been salvaged or removed from another system. Remove the key from the breakaway…

view full answer...

Answer 9

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 10

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

How is Different Gears Selected on Bulldog 2-Speed Jack # BD183401

Product Page this Question was Asked From

Continue Researching