Hardware Kit For A Demco Cast Head Coupler.

Question

Question:

Do you sale the hardware the bolts for installation?

asked by: Todd

1

Helpful Expert Reply:

I have a solution for you. We do not carry hardware kits for the Demco Cast Head Coupler w/ Jack Hole - eZ-Latch - 2" Ball - A-Frame - Bolt-On - 10K # DM37ZR. However the instructions will give you the dimensions you will need and you can pick them up from any hardware store.

expert reply by: David B

1

Answer 1

The only differences between the Demco eZ-Latch Couplers #DM37ZR and #DM14793-81 is that the former has integrated loop holes for installing safety chains and a about a 2" drop while the latter doesn't come with provisions for…

view full answer...

Answer 2

The Demco Cast Head Coupler eZ Latch #DM37ZR coms as the coupler only so you would need to supply the mounting hardware. You will need 1/2" bolts that are at least Grade 5 rated. Anything higher than that will just be even stronger and work…

view full answer...

Answer 3

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 4

I am not aware of a bolt-on version of the Buyers Products Weld-On Safety Chain Retainer part #3375471000. However, if all you were wanting to do is mount your safety chains to the tongue of your trailer then you will just simply do so by running a…

view full answer...

Answer 5

I reached out to Lets Go Aero for confirmation that you can even use the Demco 50-Degree A-Frame Coupler #DM15349-52 and they said that you will not have any structural issues with having the bolt holes drilled in the sides of your Frame as the Demco…

view full answer...

Answer 6

I have no doubts the Scissor Stabilizer Jack #TJSC-24 will work as a perfect replacement for the scissor stabilizer jacks on your 2017 Flagstaff T12RBST camper trailer because it has a large 10" x 3-1/4" mounting base with numerous…

view full answer...

Answer 7

Yes, if you wanted to weld on the Demco coupler part #DM37ZR instead of bolting it on you certainly could. This is powdercoated though so you will need to remove the powdercoating first. For a similar coupler that was designed to be welded on and…

view full answer...

Answer 8

If you look at the diagram that I received from my contact at Demco, you can see several of the dimensions of the #DM14793-81 trailer coupler. If there were other dimensions you were needing, please let me know.

view full answer...

Answer 9

Safety chains come in a variety of classes: Class I (2,000 pounds gross trailer weight or GTW), Class II (3500 pounds GTW), Class III (5,000 pounds GTW), etc. It is important that the capacity of the chains exceed your GTW, the weight of the loaded…

view full answer...

Answer 10

Demco says to use 1/2" Grade 8 bolts 1-1/2" long for the safety chains on the Demco 50-Degree A-Frame Trailer Coupler #DM16680-52. I recommend the Buyers Products 3/8" x 35" Class 4 Trailer Safety Chain #337BSC3835. You will need…

view full answer...

Answer 11

Yes, you can replace your weld-on coupler with a bolt-on. You'll just need to drill the holes. Then, if you wanted to go back to a weld-on later that would be fine too. Just to confirm you can check with the trailer's manufacturer that…

view full answer...

Answer 12

I would be happy to help! There is a few options to get the increased clearance you need to raise your trailer so you can stow away your jack when not in use. I recommend replacing the coupler with a standard a-frame coupler you would still be able…

view full answer...

Hardware Kit For A Demco Cast Head Coupler.

Product Page this Question was Asked From

Continue Researching