What Materials is CIPA Comp II Rearview mirror part # CM11081 Made From

Question

Question:

The mounting piece is aluminum, and detachable,and the mirror frame is abs plastic. What is the material for the remainder of the bracket?

asked by: George K

0

Expert Reply:

The rest of the mounting bracket of the CIPA Comp II Rearview mirror part # CM11081 that you referenced is aluminum.

expert reply by: Jameson C

0

Answer 1

Hi Jeff; thanks for the question and sturdy is definitely a good word for the etrailer tonneau that fits your 2022 Ram 1500 with a 5-1/2 foot bed, the etrailer Hard Tonneau Cover #e35DR. It's made of a fiberglass-reinforced plastic which is a…

view full answer...

Answer 2

Yes, the CE Smith Bunk-Style Guide-Ons for Boat Trailers - 60" Long - 1 Pair #CE27600 can work on the inside of a pontoon boat. Based on the photo you may prefer the CE Smith 90-Degree Bunk Board Guide-On Kit #CE27600K90 which will includes…

view full answer...

Answer 3

Yes, if you install the #MAL33TR on your Malone Microsport you'd still have the same amount of bar space to carry the same amount of kayaks as you did before. This keeps the bars still above the fenders of the trailer so you don't lose any…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The Kenda 4.80-12 Bias Trailer Tire with 12" Galvanized Wheel - 5 on 4-1/2 - Load Range B #AM30590 have a max speed of 65 mph. When trailer tires are not speed rated with a letter, the default is 65 mph max. I've attached an article to…

view full answer...

Answer 6

To measure for safety chains you will want to have the trailer hooked up to your tow vehicle with it just about jack knifed as this is the furthest the safety chains will be stretched. You will measure from one side of the tongue where you will be…

view full answer...

Answer 7

The primary difference between special trailer tires ST175/80D13 and ST175/80R13 is the type of construction. The D in the first tire size indicates bias play construction as with wheel/tire #AM3S050. For the other tire designation ST175/80R13 the R…

view full answer...

Answer 8

The CE Smith Keel Roller for Boat Trailers #CE29505 is our only self centering keel roller. It is 12" wide versus the 8" that you are looking for. We do have the CE Smith Panel Bracket for 12" Boat Trailer Rollers #CE10305G and Roller…

view full answer...

Answer 9

In height or total diameter, a 185/80-13 and 175/80-13 like part #AM1ST77 only differ by about 5/8 of an inch. The 185 would have a diameter of 24.65 inches while the 175 would have a diameter of 24.02 inches. The section width, or thickness of the…

view full answer...

Answer 10

The galvanized finish is better for salt water than your white powder coated wheels. If you want the best wheel for use in salt water you will want to use an aluminum wheel. I see that you were looking at the Loadstar ST175/80D13 Bias Trailer Tire…

view full answer...

Answer 11

Replacement bearings, races, seals, etc. can best be identified using the original part numbers, but in cases where those part numbers are not available it is possible to measure the trailer spindles with a precision caliper (to the nearest…

view full answer...

What Materials is CIPA Comp II Rearview mirror part # CM11081 Made From

Product Page this Question was Asked From

Continue Researching