Replacement Brake Assemblies for 2,200 lb Reliable Trailer Axles

Question

Question:

My Triton Trailer has 2200 Pound Reliable Brand Axels.. Reliable Model 08479 I am looking for an Electric Brake Kit.. Both Axels I live in the mountains if not cost prohibitive or just one axel..

asked by: Bill M

0

Expert Reply:

For 2,200 lb trailer axles like what your trailer has the correct brake assembly set is the part # K23-103-104-00 which will give you a left and right hand assembly.

expert reply by: Jameson C

0

Answer 1

We have an option to replace the torsion axle on your 1996 Triton snowmobile trailer, but do not carry any torsion axles. Instead, the best option we have is a Timbren Axle-Less trailer suspension system which are simply bolted or welded so you do…

view full answer...

Answer 2

You are only be able to add parking brakes to your trailer brakes if those brake assemblies are already equipped with a parking brake actuator. You can tell if your brakes are equipped with a parking brake by looking at the backing plate-there will…

view full answer...

Answer 3

Most trailers do not come with parking brakes, but you can add them with certain electric brake assemblies. If your trailer has 7 inch brakes, then you will want the Dexter Electric Trailer Brake Kit w/ Parking Brakes - 7" - Left/Right Hand…

view full answer...

Answer 4

Yes, the Optronics Trailer Tail Light part #ST70RB will be a direct replacement for your Truck-Lite Trailer Tail Light part 60210R. They both have the same dimensions and the plug is the exact same. If your trailer lights are not working then make…

view full answer...

Answer 5

We do not have any types of parts lists for specific trailers, so in order to choose the correct replacement axle, you will need to know the dimensions of your current axle's hub-face to hub-face and spring center to spring center as in the…

view full answer...

Answer 6

By Sure Lube you mean like an EZ Lube setup that has zerk fittings on the ends of the spindles to grease through the middle of the hub? That's what I was able to find when Googling your setup. If so, you can install a Bearing Buddy over this…

view full answer...

Answer 7

If you want to use a Bearing Buddy on a trailer hub that currently has a Sure Lube grease cap you certainly could. Essentially the design between the two is the same.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Replacement Brake Assemblies for 2,200 lb Reliable Trailer Axles

Product Page this Question was Asked From

Continue Researching