Installation Location for the Bright Way Push to Test Breakaway Kit

Question

Question:

Can it be bolt on a flat surface

asked by: Carl

0

Expert Reply:

Yes, you can bolt the Bright Way Push-to-Test ICU Trailer Breakaway Kit item # BW94FR to a flat surface to install it. I have attached an installation video to walk you through the process.

expert reply by: Jerred H

0

Answer 1

You definitely can use the Optronics Thinline LED Trailer Tail Light #STL64RB as a 3rd brake light! You'll need to cap off the black wire, ground the white wire, and then install the Pacer Performance 3rd Brake Light Logic Module #PP20-702…

view full answer...

Answer 2

The lid of the Bright Way Trailer Breakaway ICU Kit with 12V, 5-Amp-Hour Battery, Charger, and Wire Loom #BW94FR that you referenced has a wiring diagram shown that details how it wires. Not seen is there is a single wire that runs up to running…

view full answer...

Answer 3

The Optronics light best suited to your application as a 3rd brake light is their part #STL80RB which is a single-function LED light. The light #STL64RB that you referenced is a multi-function light (Stop/Turn/Tail) which you do not need. It is…

view full answer...

Answer 4

The video review for the Optronics Thinline LED Trailer Tail Light #STL64RB that you mentioned is correct. The white wire is for ground, the black wire is for tail lights, and the red wire is for turn/brake signals.

view full answer...

Answer 5

Both the Peterson Piranha LED Clearance and Side Marker Trailer Light w/ Turn Signal #M353A and Miro-Flex LED Trailer Side Marker Light and Mid-Ship Turn Signal #OPT78FR are sold individually. We do not offer them as a pair for lower price. Since you…

view full answer...

Answer 6

No, the battery charger included with the Bright Way Breakaway Battery #BW94FR will not overcharge the battery no matter how far you drive. It is designed to allow the battery to fully charge, and then keep it there without damaging the battery.

view full answer...

Answer 7

The breakaway system actually must be attached to its own separate battery by law in most states. Therefore, I cannot recommend that you use a seperate, auxiliary battery on the trailer or the vehicle for that matter for the breakaway switch. The…

view full answer...

Answer 8

I would not recommend installing a Diode #RM-690 on the brake line as this is a part which can fail and if it were to you could risk doing a lot of damage. While the Bright Way Push-to-Test ICU Trailer Breakaway Kit #BW94FR could risk damage to your…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

You have it right so far, the 4-way connector is just as you have stated. Remember that Yellow has a L in it so that is the left side brake/turn signal and green has a R in it so that is the right side brake/turn signal. The colors for wiring a 7-way…

view full answer...

Installation Location for the Bright Way Push to Test Breakaway Kit

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching