Compatibility Of Derale Transmission Cooler for a 2018 Chevrolet Colorado 2.8L Duramax Diesel

Question

Question:

I installed this on a 2017 traverse and saw amazing results towing. Curious if it’s worthwhile and recommend on my 2018 Chevy Colorado 2.8L Duramax diesel?

asked by: Josh H

0

Expert Reply:

Yes, you can also install the Derale Series 8000 Plate-Fin Transmission Cooler # D13503 on your 2018 Chevrolet Colorado with the 2.8L Duramax engine. This cooler is a great addition to most vehicles that are towing, especially in the hotter climates or are subjected to a lot of stress when towing(stop and go). Installation is made easier on your Colorado with a Derale Snap-In Radiator Adapter Fitting # D13035 that allow you to not have to cut your transmission lines.

By keeping the transmission cool it will increase the life of your transmission by reducing the wear of the clutches inside as well as the sensitive electronics that monitor and control the transmission. This also helps prevent the computer in your Colorado from cutting engine power when the transmission heats to levels that will damage the components inside the transmission.

I have linked a helpful installation video that we did on a 2017 GMC Canyon that you can reference.

expert reply by: Bud M

0

Answer 1

To install a Derale transmission cooler on your 2010 GMC Canyon you will need one of the Derale Snap-In Radiator Adapter Fitting for GM, #D13035. This will snap into the factory transmission coolers output fitting to allow you to run the coolant line…

view full answer...

Answer 2

The best transmission cooler for your 2016 Chevy Colorado with a 2.8L diesel engine is the Derale Series 8000 Plate-Fin Transmission Cooler #D13503. This is the best transmission cooler because of how efficient it is; this is a plate-and-fin cooler,…

view full answer...

Answer 3

A stacked-plate cooler has the same design as a plate-fin, but it uses high-flow turbulators which makes it more efficient. Stacked-plate is typically for heavy-duty towing, and I don't think you need a combination cooler either. In your case, I…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

The 2016 Chevrolet Colorado does not have a plug-in adapter for a brake controller such as the Tekonsha Prodigy P3 Trailer Brake Controller part #90195. However, the wires that will need to be hardwired into the adapter are already present on the…

view full answer...

Answer 8

I recommend using the Curt Lock Set #C23556 for your Curt Adjustable 2-Ball Mount #C99NR. This comes with a lock for the hitch receiver and one for the ball mount platform. Even though your platform uses 2 pins, only 1 locking pin is needed to secure…

view full answer...

Answer 9

You can install a stack cooler in your vehicle. The Class ratings are there as a reference point to a hitch Class. For example if someone has a Class III hitch they can look at coolers, see a Class III and say, hey, I have a Class III hitch so this…

view full answer...

Answer 10

Hey Jerry, the install of the Aries Bull Bar part #AAB35-4015 do require you to permanently remove the tow hooks to install. It looks like the similar Westin Ultimate Bull Bar part #32-3645 does allow you to keep them though.

view full answer...