Taillight Converter Needed To Separate Brake Lamp and Turn Signal Circuits

Question

Question:

I have a custom built trailer that ive already out fitted with lights, but due to its size i would like to put separate turn/brake lights on it without them being combined. Can i attach this onto my trailer and wire it into the existing wiring to get those separate signals?

asked by: Kyle

0

Expert Reply:

The Curt # C56196 2 to 3 wire taillight converter is exactly what you'll need to split out the turn signal function from the brake lamp circuit. However, keep in mind that the # C56196 is NOT compatible with LED lamps, unfortunately we don't offer a taillight converter at this time that is compatible with LED lamps.

You would wire the converter inline with the right and left turn and brake circuits. You will want to install the converter some place where it's protected from the elements. If the design of the trailer makes that difficult or impossible, then you can use a junction box like # 3375601100 to protect the converter.

I've linked to the installation instructions for you.

expert reply by: Mike L

0

Wiring Diagram for Curt C56196 2-Wire to 3-Wire Taillight Converter.
(click to enlarge)

Answer 1

Those are the wires for the brake magnets. You will need to connect the black wire to the brake controller output wire on your trailer connector and you are correct the white wire will need to be grounded to a clean metal surface on the trailer. I…

view full answer...

Answer 2

The ring terminals you want to use with the junction #3375601100 are the #44-5310A which have an inner diameter of 3/16 of an inch.

view full answer...

Answer 3

Can you tell me what axle capacity the trailer has? I don't have the ability to look up trailer component info based on the VIN at this time.

view full answer...

Answer 4

If your trailer has separate turn signals from the brake lights and you want them to remain that way, you will need to use a special converter. On the trailer side, behind the 7-Way, you will attach the Vehicle to Vehicle Taillight Converter,…

view full answer...

Answer 5

If I understand you correct you have a trailer with separate turn signals and brake lights that aren't functioning properly because you 2013 Ford F-150's trailer wiring combines those signals on one circuit. If I'm wrong let me know. If…

view full answer...

Answer 6

Either way is correct. It depends on if you want to keep the semi-style 7-Way (if you need to tow that type of trailer) or if you will never be towing a semi-trailer. If you need to keep the 7-Way semi active on the truck, then you would need to make…

view full answer...

Answer 7

The Hopkins taillight converter part #HM48847 is the current version of the 48845 that it replaced which can work for your application. It will combine the separate turn signal circuits you have on your trailer like you are needing.

view full answer...

Answer 8

The Prodigy P3 part #90195 will work for you because your trailer has electric brakes. The P3 can install and work just fine on vehicles with air brakes. The only thing it needs from the vehicle is access to a circuit that only sees voltage when the…

view full answer...

Answer 9

There are two options for a wiring harness for your 2020 Chevy Equinox depending on what model you have. If you have LED tail lights you will want the Roadmaster Smart Diode 7-Wire to 6-Wire Wiring Kit for Variable Voltage LED Tail Lights item…

view full answer...

Answer 10

The Malone Hanger Spare Tire Bike Rack for 3 Bikes #MPG2147 will fit on the 255/70R18 spare tire at the back of your 2021 Ford Bronco. The Malone rack is designed to fit 8" to 10-1/2" wide tires and your tire is 10" wide so it will…

view full answer...

Answer 11

There's not a universal way that trailers are wired. I have attached a diagram showing the three typical ways and this should also help you to connect to the 7-way harness you purchased once you identify your wires. Yours is obviously different,…

view full answer...